Radiator and Hydraulic Oil Cooler - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 140-7742     | 套筒     | 2     |
B     | 189-0408     | 钩环组件     | 2     |
- 将工具 (A) 、工具 (B) 和适当的起吊设备固定到散热器和液压油冷却器组件 (27) 上。 散热器和液压油冷却器组件 (27) 的重量约为 544 kg (1200 lb)。
Show/hide table
图 1 | g01707795 |
Show/hide table
图 2 | g01707796 |
- 定位散热器和液压油冷却器组件 (27) ,并安装螺栓 (28) 。
- 安装面板 (26) 。
Show/hide table
图 3 | g01707794 |
- 定位软管组件 (25) 。 将软管组件 (25) 连接到支承 (24) 。 连接软管组件 (25) 。 安装支架和乙醚启动阀 (21) 。 连接线束组件 (23) 。 连接管组件 (22) 。
Show/hide table
图 4 | g01707793 |
- 将支架 (20) 放置到位。 将支架 (20) 连接到支承 (16) 上。
Show/hide table
图 5 | g01707678 |
- 对于另一侧,重复步骤5。
- 连接管 (19) 。
Show/hide table
图 6 | g01707760 |
- 连接软管 (18) 。
Show/hide table
图 7 | g01707759 |
- 将支架 (17) 连接到支承 (16) 上。
Show/hide table
图 8 | g01707676 |
- 将软管组件 (15) 连接到风扇马达上。
Show/hide table
图 9 | g01707357 |
- 将管 (13) 和 (14) 作为一个整体安装。
Show/hide table
图 10 | g01707355 |
- 安装管 (7) 和 (12) 。 将软管 (8) 和 (9) 连接到散热器上。 将软管 (9) 固定护罩 (11) 上。 安装支承 (10) 。
Show/hide table
图 11 | g01707354 |
- 将合适的起吊设备连接到发动机罩组件 (5) 上。 发动机罩组件 (5) 的重量约为 68 kg (150 lb)。
Show/hide table
图 12 | g01707758 |
- 安装发动机罩组件 (5) 。 安装螺栓 (6) 。
- 关闭检修门 (4) 。 关闭机器左侧的检修门。 安装螺栓 (3) 。
Show/hide table
图 13 | g01707756 |
- 向液压油箱注油。 请参阅操作和保养手册, "液压系统机油 – 更换"。
- 向冷却系统加注冷却液。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
- 安装防护装置 (1) 和 (2) 。
Show/hide table
图 14 | g01707754 |
Caterpillar Information System:
345D and 349D Excavators C13 Engine Supplement Radiator and Hydraulic Oil Cooler - Remove
Installation and Adjustment Procedure for the 332-8662 Actuator Kit (Wastegate){1052, 1053, 1057, 1940} Installation and Adjustment Procedure for the 332-8662 Actuator Kit (Wastegate){1052, 1053, 1057, 1940}
3512B HD SR500 Generator Sets Configuration Parameters
Installation Procedure for the Space Heater On Generator Sets{4450} Installation Procedure for the Space Heater On Generator Sets{4450}
TH55FT-E70 and TH55FT-E90 Transmissions General Hazard Information
C18 Fire Pump Industrial Engine Jacket Water Heater - Remove and Install
R250 Automatic Voltage Regulator Constant Volts Per Hertz Operation - Using Knee Frequency Control
2008/11/01 A New Outer Valve Spring Is Now Used {1100, 1108}
2008/12/08 A New Outer Valve Spring is Now Used {1100, 1108}
2008/11/17 A New Outer Valve Spring Is Now Used {1100, 1108}
120K Motor Grader Hydraulic System Oil Level - Check
2008/12/22 A New Turbocharger Cartridge is Used {1052, 1053}
3508, 3512, and 3516 Generator Sets Refill Capacities and Recommendations
TH55FT-E70 and TH55FT-E90 Transmissions Transmission Warm-up
345D and 349D Excavators C13 Engine Supplement Fan - Install
2008/11/10 New Starter Lines Group and Prelube Pump Group Are Used {1319, 1451}
345D and 349D Excavators C13 Engine Supplement Fan Drive - Remove
345D and 349D Excavators C13 Engine Supplement Fan Drive - Install
TH48-E80 Petroleum Transmission Oil Filter (Transmission)
C18 Fire Pump Industrial Engine Cylinder Head - Remove
345D and 349D Excavators C13 Engine Supplement Engine - Remove
345D and 349D Excavators C13 Engine Supplement Engine - Install
2009/01/26 Troubleshooting the Wastegate Canister {1052, 1057}
2008/12/22 Troubleshooting the Wastegate Canister {1052, 1057}