IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Caterpillar

Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed.

The user is responsible for the performance of maintenance. All adjustments, the use of proper lubricants, fluids, filters, and the replacement of components due to normal wear and aging are included. Failure to adhere to proper maintenance intervals and procedures may result in diminished performance of the product and/or accelerated wear of components.

Use mileage, fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, in order to determine the maintenance intervals. Products that operate in severe operating conditions may require more frequent maintenance. Refer to the maintenance procedure for any other exceptions that may change the maintenance intervals.

Note: The aftertreatment system can be expected to function properly for the useful life of the engine (emissions durability period), as defined by regulation. All prescribed maintenance requirements must be followed.

Note: Before each consecutive interval is performed, all maintenance from the previous interval must be performed.

Note: If Cat HYDO Advanced hydraulic oils are used, the hydraulic oil change interval is extended substantially. S·O·S services may extend the oil change even longer. Consult your Cat dealer for details.

The following guidelines should be followed if the service hours are not met:

Items listed between 10 and 100 service hours should be performed at least every 3 months.

Items listed between 250 and 500 service hours should be performed at least every 6 months.

Items listed between 1000 service hours and 2500 service hours should be performed at least every year.

When Required

Automatic Lubrication Grease Tank - Fill
Battery or Battery Cable - Inspect/Replace
Bucket Cutting Edges - Inspect/Replace
Bucket Hinge and Lift Arm Clearance Shims - Inspect/Adjust/Replace
Bucket Tips - Inspect/Replace
Camera - Clean
Circuit Breakers - Reset
Engine Air Filter Primary Element - Clean/Replace
Engine Air Filter Secondary Element - Replace
Ether Starting Aid Cylinder - Replace
Fuel System - Prime
Fuses - Replace
High Intensity Discharge Lamp (HID) - Replace
Oil Filter - Inspect
Pallet Fork - Inspect
Radiator Core - Clean
Ride Control Accumulator - Check
Secondary Steering - Test
Window Washer Reservoir - Fill
Window Wiper - Inspect/Replace

Every 6000 Service Hours or 3 Years

Cooling System Coolant Extender (ELC) - Add

Every 6000 Service Hours or 6 Years

Cooling System Water Temperature Regulator - Replace

Every 12 000 Service Hours or 6 Years

Cooling System Coolant (ELC) - Change

Every 10 Service Hours or Daily

Backup Alarm - Test
Cooling System Coolant Level - Check
Engine Oil Level - Check
Fuel System Primary Filter (Water Separator) - Drain
Hydraulic System Oil Level - Check
Quick Coupler - Check
Seat Belt - Inspect
Transmission Oil Level - Check
Windows - Clean

Every 50 Service Hours or Weekly

Bucket Lower Pivot Bearings - Lubricate
Cab Air Filter - Clean/Replace
Fuel Tank Water and Sediment - Drain
Tire Inflation - Check

Every 100 Service Hours or 2 Weeks

Axle Oscillation Bearings - Lubricate
Bucket Linkage and Loader Cylinder Bearings - Lubricate
Bucket Upper Pivot Bearings - Lubricate
Logging Fork Clamp - Lubricate
Steering Cylinder Bearings - Lubricate

Initial 250 Service Hours

Engine Valve Lash - Check
Transmission Oil Filter - Replace

Every 250 Service Hours

Cooling System Coolant Sample (Level 1) - Obtain
Drive Shaft Support Bearing - Lubricate
Engine Oil Sample - Obtain

Every 250 Service Hours or Monthly

Battery - Clean
Belt - Inspect/Adjust/Replace
Brake Accumulator - Check
Braking System - Test
Differential and Final Drive Oil Level - Check
Drive Shaft Spline (Center) - Lubricate
Quick Coupler - Lubricate

Every 250 Service Hours or 3 Months

Engine Oil and Filter - Change
Pallet Fork - Lubricate
Steering Column Play - Check

Every 500 Service Hours

Hydraulic System Oil Filter - Replace
Hydraulic System Oil Sample - Obtain
Transmission Oil Filter - Replace

Every 500 Service Hours or 3 Months

Differential and Final Drive Oil Sample - Obtain
Engine Crankcase Breather - Clean
Engine Oil and Filter - Change
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Fuel Tank Cap and Strainer - Clean
Hydraulic System Biodegradable Oil Filter Element - Replace
Transmission Oil Sample - Obtain

Every 1000 Service Hours or 6 Months

Articulation Bearings - Lubricate
Battery Hold-Down - Tighten
Case Drain Screen (Strainer) (Steering Pump, Hydraulic Fan Pump, Motor) - Clean
Drive Shaft Universal Joints - Lubricate
Roading Fender Hinges - Lubricate
Rollover Protective Structure (ROPS) - Inspect
Steering Pilot Oil Screen (Command Control Steering) - Clean/Replace
Transmission Oil - Change

Every 2000 Service Hours

Hydraulic Tank Breaker Relief Valve - Clean

Every 2000 Service Hours or 1 Year

Brake Discs - Check
Differential and Final Drive Oil - Change
Engine Valve Lash - Check
Engine Valve Rotators - Inspect
Hood Tilt Actuator - Lubricate
Service Brake Wear Indicator - Check
Steering Column Spline (Command Control Steering) - Lubricate

Every Year

Cooling System Coolant Sample (Level 2) - Obtain
Receiver Dryer (Refrigerant) - Replace

Every 3000 Service Hours

Hydraulic System Oil - Change
Steering Column Spline (HMU Steering) - Lubricate

Every 3 Years

Seat Belt - Replace