Differential and Pinion - Assemble - Locking
- Install thrust washer (12) and differential gear (11) into the lower half of case assembly (13).
Show/hide table
Illustration 2 g01394898 - Install sleeve bearing (9) onto spider (10). Install differential pinion (8) and thrust washer (7). Make sure that all differential pinions (8) turn freely.
Show/hide table
Illustration 3 g01673239 - Install spider and gear assembly (6).
Note: .The protrusions on the spider face downward in the direction of the locking pin.
Show/hide tableIllustration 4 g01394858 - Install the upper half of case assembly (5).
Show/hide table
Illustration 5 g01394857 - Install differential gear (4) and thrust washer (3).
Show/hide table
Illustration 6 g01394855 - Raise the temperature of ring gear to a maximum temperature of
135 °C (275 °F) for a maximum of 4 hours. Install ring gear (2). Make sure that the holes for bolts (1) are aligned with the differential case. Allow ring gear (2) to cool to room temperature. - Lubricate the washers and the threads of bolts (1). Install new bolts (1). Tighten bolts (1) to the correct torque specified in Table 1.
Show/hide table
Table 1 Torque Chart for bolts (1) Machine Serial Number Initial Torque Torque Turn 926 (S/N: LTE1-UP) 120 ± 20 N·m (89 ± 15 lb ft) - 930 (S/N: TNY1-UP) (S/N: KTG1-UP) (S/N: HEY1-UP) 95 ± 10 N·m (70 ± 7 lb ft) 180° ± 5°
Show/hide table
Illustration 1 | g01394899 |
End By:
- Install the differential.
Caterpillar Information System:
926M, 930M and 938M Wheel Loaders Power Train Differential and Pinion - Disassemble - Locking
D6R2 Track-Type Tractor Engine Supplement Engine Front Support - Remove and Install
834K Wheel Dozer Maintenance Interval Schedule
D6R2 Track-Type Tractor Engine Supplement Valve Cover - Remove and Install
926M, 930M and 938M Wheel Loaders Power Train Differential and Pinion - Remove and Install - Standard
D6R2 Track-Type Tractor Engine Supplement Turbocharger - Remove and Install
926M, 930M and 938M Wheel Loaders Power Train Differential and Pinion - Remove and Install - Locking
D7E Track-Type Tractor Systems Pump Control Valve (Implement)
D6R2 Track-Type Tractor Engine Supplement Secondary Fuel Filter and Base - Remove and Install
D7E Track-Type Tractor Systems Sweep Group
D7E Track-Type Tractor Systems Final Drive Mounting
D7E Track-Type Tractor Systems Lift Cylinder (Bulldozer)
D6R2 Track-Type Tractor Engine Supplement Engine Trunnion - Remove and Install
926M, 930M and 938M Wheel Loaders Power Train Differential and Pinion - Disassemble - Standard
D6R2 Track-Type Tractor Engine Supplement Water Temperature Regulator - Remove and Install
926M, 930M and 938M Wheel Loaders Power Train Differential and Pinion - Assemble - Standard
Specifications and Salvage for Well Stimulation Fluid End {0374, 0599, 0679, 5070, 7000} Specifications and Salvage for Well Stimulation Fluid End {0374, 0599, 0679, 5070, 7000}
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Maintenance Interval Schedule
Installation of the Winch on the D3K2, D4K2, and D5K2 Track-Type Tractors {5163} Installation of the Winch on the D3K2, D4K2, and D5K2 Track-Type Tractors {5163}
C27 and C32 Engines for Caterpillar Built Machines Oil Level - Test
335F CR Excavator C7.1 Engine Supplement Nitrogen Oxide Sensor - Remove and Install - Outlet
D6R2 Track-Type Tractor Engine Supplement Water Pump - Remove and Install
335F CR Excavator C7.1 Engine Supplement Nitrogen Oxide Sensor - Remove and Install - Inlet
335F CR Excavator C7.1 Engine Supplement Fan - Remove and Install