Water Pump - Remove
Removal Procedure
Start By:
- Remove the water temperature regulator housing. Refer to Disassembly and Assembly, "Water Temperature Regulator Housing - Remove".
- Remove the clean clean gas induction cooler. Refer to Disassembly and Assembly, "Clean Gas Induction Cooler - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Remove elbow (1). Remove bracket (2) .
Show/hide table
Illustration 1 | g01288692 |
- Disconnect hose (3). Disconnect tube assembly (5). Remove nut (6) and the stud. Disconnect tube assembly (7). Remove bolts (4). Remove elbow (8) .
Show/hide table
Illustration 2 | g01288715 |
- Disconnect hose (9). Remove bolts (10). Remove elbow (11) .
Show/hide table
Illustration 3 | g01288725 |
- Loosen bolts (12) by approximately 25 mm (1 inch) in order to separate water pump (13) from front housing (14) .
Show/hide table
Illustration 4 | g01288797 |
- Remove water pump (13) .
- Remove O-ring seal (15) from water pump (13) .
Show/hide table
Illustration 5 | g01288803 |
Caterpillar Information System:
2006/08/07 A New Kit for the Cooling System Pressure Cap is Available {1353, 1354, 1382, 1392, 7405}
3508B, 3512B, and 3516B High Displacement Generator Sets Overhaul (Top End)
3508B, 3512B, and 3516B High Displacement Generator Sets Overhaul (Major)
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Control Manifold - Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Control Manifold - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Transmission Lubrication) - Assemble
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Transmission Lubrication) - Disassemble
C15 On-Highway Engine Clean Gas Induction Valve - Install
C15 On-Highway Engine Clean Gas Induction Valve - Remove
Reuse and Salvage for Connecting Rods {1218} Reuse and Salvage for Connecting Rods {1218}
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Transmission Lubrication) - Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Relief Valve (Transmission Lubrication) - Remove
C15 On-Highway Engine Water Pump - Install
3512C Petroleum Engines Analog Sensor (Passive)
C15 On-Highway Engine Water Temperature Regulator Housing - Remove and Install
C175-16 and C175-20 Generator Set Engines Finding the Top Center Position for the No. 1 Piston
C15 On-Highway Engine Engine Oil Filter Base - Remove
C15 On-Highway Engine Engine Oil Filter Base - Install
G3500 Engines Flywheel
C175-16 Locomotive Engine Valve Lash - Adjust
3500B Generator Sets Emergency Stopping
C15 On-Highway Engine Valve Mechanism Cover - Remove and Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Transfer Gears - Remove - Idler
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Transfer Gears - Install - Idler