Valve Mechanism Cover - Remove and Install
Removal Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove clips (1). Remove hose (2). Remove adapter (3). Remove hose (4) .
Show/hide table
Illustration 1 | g01289969 |
Show/hide table
Illustration 2 | g01290041 |
- Remove bolts (5). Remove valve mechanism cover (6) .
Show/hide table
Illustration 3 | g01289972 |
- Remove isolation seal (7). Discard isolation seal (7) .
Show/hide table
Illustration 4 | g01290064 |
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position a new isolation seal (7) onto the valve cover base. Align isolation seal (7) by using the locator pins.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Show/hide table
Illustration 5 | g01290064 |
- Position valve mechanism cover (6) on the valve cover base. Install bolts (5). Tighten bolts (5) to a torque of 25 ± 6 N·m (18 ± 4 lb ft).
Show/hide table
Illustration 6 | g01289972 |
- Install hose (4). Install adapter (3). Install hose (2). Install clips (1) .
Show/hide table
Illustration 7 | g01290041 |
Show/hide table
Illustration 8 | g01289969 |
Caterpillar Information System:
3500B Generator Sets Emergency Stopping
C175-16 Locomotive Engine Valve Lash - Adjust
G3500 Engines Flywheel
C15 On-Highway Engine Engine Oil Filter Base - Install
C15 On-Highway Engine Engine Oil Filter Base - Remove
C175-16 and C175-20 Generator Set Engines Finding the Top Center Position for the No. 1 Piston
C15 On-Highway Engine Water Temperature Regulator Housing - Remove and Install
3512C Petroleum Engines Analog Sensor (Passive)
C15 On-Highway Engine Water Pump - Install
C15 On-Highway Engine Water Pump - Remove
2006/08/07 A New Kit for the Cooling System Pressure Cap is Available {1353, 1354, 1382, 1392, 7405}
3508B, 3512B, and 3516B High Displacement Generator Sets Overhaul (Top End)
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Transfer Gears - Remove - Idler
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Transfer Gears - Install - Idler
2006/07/01 A New Backup Ring for the Fuel Injector Group is Now Available {1251, 1254, 1290}
C11 and C13 Engines Valve Mechanism Cover - Remove and Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Modulating Valve (Transmission Clutch) - Remove and Install
C27 and C32 Generator Set Engines Fan Drive - Remove and Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Install
C32 Power Module Heat Shield - Inspect/Replace
C27 and C32 Generator Set Engines Belt Guard - Remove and Install
C27 and C32 Generator Set Engines Fan - Remove and Install
C27 and C32 Generator Set Engines Fan Guard - Remove and Install