Modulating Valve (Transmission Clutch) - Remove and Install
拆卸步骤
注: 清洁度是一项重要的因素。 解体步骤开始之前,应彻底清洁部件外部。 这将有助于防止脏污进入内部机构。
注: 为便于安装,在所有管路、所有软管、所有线束组件及所有管上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和有助于防止污染物进入系统。
- 卸下螺栓 (1) 和盘 (2) 。
Show/hide table
图 1 | g01289505 |
- 断开线束组件 (3) 和软管组件 (4) 。
Show/hide table
图 2 | g01289506 |
- 卸下螺栓 (6) 和调节阀 (5) 。
- 从调节阀 (5) 上卸下 O 形密封圈 (8) 。
Show/hide table
图 3 | g01289549 |
- 卸下螺母 (9) 和线圈组件 (7) 。
- 对于其余的调节阀,重复步骤 2 至 5。
安装步骤
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零部件上,从而可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新件进行更换。
- 安装线圈组件 (7) 和螺母 (9) 。 拧紧螺母 (9) 到扭矩为 13 ± 1.5 N·m (10 ± 1 lb ft)。
Show/hide table
图 4 | g01289549 |
- 将 O 形密封圈 (8) 安装到调节阀 (5) 上。
- 安装调节阀 (5) 和螺栓 (6) 。
Show/hide table
图 5 | g01289506 |
- 连接线束组件 (3) 和软管组件 (4) 。
- 对于其余的调节阀,重复步骤 1 至 4。
- 安装盘 (2) 和螺栓 (1) 。
Show/hide table
图 6 | g01289505 |
Caterpillar Information System:
C11 and C13 Engines Valve Mechanism Cover - Remove and Install
2006/07/01 A New Backup Ring for the Fuel Injector Group is Now Available {1251, 1254, 1290}
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Transfer Gears - Install - Idler
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Transfer Gears - Remove - Idler
C15 On-Highway Engine Valve Mechanism Cover - Remove and Install
3500B Generator Sets Emergency Stopping
C175-16 Locomotive Engine Valve Lash - Adjust
G3500 Engines Flywheel
C15 On-Highway Engine Engine Oil Filter Base - Install
C15 On-Highway Engine Engine Oil Filter Base - Remove
C175-16 and C175-20 Generator Set Engines Finding the Top Center Position for the No. 1 Piston
C15 On-Highway Engine Water Temperature Regulator Housing - Remove and Install
C27 and C32 Generator Set Engines Fan Drive - Remove and Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Install
C32 Power Module Heat Shield - Inspect/Replace
C27 and C32 Generator Set Engines Belt Guard - Remove and Install
C27 and C32 Generator Set Engines Fan - Remove and Install
C27 and C32 Generator Set Engines Fan Guard - Remove and Install
C15 On-Highway Engine Valve Mechanism Cover Base - Remove and Install
C32 Power Module Air Inlet Filter - Check
3612 and 3616 Engines Fuel Priming Pump - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Disassemble
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Assemble