Torque Converter - Install
安装步骤
Show/hide table
需要的工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
A     | 1U-9200     | 杠杆式拔拉起重机     | 1     |
B     | 138-7575     | 连杆支架     | 3     |
C     | 189-0409     | 钩环组件     | 2     |
D     | 1P-2420     | 变速箱修复台     | 1     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零部件上,从而可能导致以后出现故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新件进行更换。
- 将 O 形密封圈 (4) 安装到壳体中。
Show/hide table
图 1 | g01289643 |
- 使用工具 (B) 和适当的起吊设备,将变矩器 (2) 安置在壳体中。 变矩器 (2) 的重量约为 365 kg (805 lb)。
Show/hide table
图 2 | g01289639 |
- 安装螺栓 (3) 。
Show/hide table
图 3 | g01289640 |
- 使用工具 (A) 、工具 (B) 、工具 (C) 和适当的起吊设备,从工具 (D) 上卸下变矩器壳体 (1) 。 变矩器和变矩器壳体 (1) 的重量约为 590 kg (1300 lb)。
Show/hide table
图 4 | g01289637 |
End By: 安装分动器。 请参阅 解体和组装, "分动器 - 安装"。
Caterpillar Information System:
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Remove
C27 and C32 Generator Set Engines Fan Drive - Remove and Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Modulating Valve (Transmission Clutch) - Remove and Install
C11 and C13 Engines Valve Mechanism Cover - Remove and Install
2006/07/01 A New Backup Ring for the Fuel Injector Group is Now Available {1251, 1254, 1290}
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Transfer Gears - Install - Idler
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Transfer Gears - Remove - Idler
C15 On-Highway Engine Valve Mechanism Cover - Remove and Install
3500B Generator Sets Emergency Stopping
C175-16 Locomotive Engine Valve Lash - Adjust
G3500 Engines Flywheel
C15 On-Highway Engine Engine Oil Filter Base - Install
C32 Power Module Heat Shield - Inspect/Replace
C27 and C32 Generator Set Engines Belt Guard - Remove and Install
C27 and C32 Generator Set Engines Fan - Remove and Install
C27 and C32 Generator Set Engines Fan Guard - Remove and Install
C15 On-Highway Engine Valve Mechanism Cover Base - Remove and Install
C32 Power Module Air Inlet Filter - Check
3612 and 3616 Engines Fuel Priming Pump - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Disassemble
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Assemble
3612 and 3616 Engines Fuel Priming Pump - Install
Caterpillar Logic Control Governor One (LCG1) and Caterpillar Logic Control Governor Two (LCG2){1264, 1908} Caterpillar Logic Control Governor One (LCG1) and Caterpillar Logic Control Governor Two (LCG2){1264, 1908}
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System Transmission Control (Shift Solenoid) - Calibrate