Fan Drive - Remove and Install
拆卸步骤
开始:
- 拆下风扇。 请参阅拆解和组装, "风扇 - 拆卸和安装"。
- 拆下传动皮带护罩。 请参阅拆解和装配, "皮带护罩 - 拆卸和安装"。
- 卸下皮带。 参考操作和保养手册, "皮带 - 检查/调整/更换"。
- 松开螺栓 (1) 。 松开锁紧螺母 (2) 。
Show/hide table
图 1 | g01289585 |
- 将适当的起吊设备连接到风扇驱动 (3) 上。 风扇驱动装置 (3) 的重量约为 45 kg (100 lb)。 拆下螺栓 (1 ) 。 卸下风扇驱动 (3) 。
Show/hide table
图 2 | g01289589 |
安装步骤
- 将适当的起吊设备连接到风扇驱动 (3) 上。 风扇驱动装置 (3) 的重量约为 45 kg (100 lb)。 安装风扇驱动 (3) 。 安装螺栓 (1) 。
Show/hide table
图 3 | g01289589 |
- 安装皮带。 参考操作和保养手册, "皮带 - 检查/调整/更换"。
Show/hide table
图 4 | g01289585 |
- 拧紧螺栓 (1) 。 拧紧锁紧螺母 (2) 。
End By:
- 安装皮带护罩。 请参阅 拆解和装配, "皮带护罩 - 拆卸和安装"。
- 安装风扇。 请参阅 拆解和组装, "风扇 - 拆卸和安装"。
Caterpillar Information System:
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Modulating Valve (Transmission Clutch) - Remove and Install
C11 and C13 Engines Valve Mechanism Cover - Remove and Install
2006/07/01 A New Backup Ring for the Fuel Injector Group is Now Available {1251, 1254, 1290}
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Transfer Gears - Install - Idler
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Transfer Gears - Remove - Idler
C15 On-Highway Engine Valve Mechanism Cover - Remove and Install
3500B Generator Sets Emergency Stopping
C175-16 Locomotive Engine Valve Lash - Adjust
G3500 Engines Flywheel
C15 On-Highway Engine Engine Oil Filter Base - Install
C15 On-Highway Engine Engine Oil Filter Base - Remove
C175-16 and C175-20 Generator Set Engines Finding the Top Center Position for the No. 1 Piston
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Install
C32 Power Module Heat Shield - Inspect/Replace
C27 and C32 Generator Set Engines Belt Guard - Remove and Install
C27 and C32 Generator Set Engines Fan - Remove and Install
C27 and C32 Generator Set Engines Fan Guard - Remove and Install
C15 On-Highway Engine Valve Mechanism Cover Base - Remove and Install
C32 Power Module Air Inlet Filter - Check
3612 and 3616 Engines Fuel Priming Pump - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Disassemble
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Assemble
3612 and 3616 Engines Fuel Priming Pump - Install