Torque Converter - Remove
拆卸步骤
Show/hide table
需要的工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
A     | 1U-9200     | 杠杆式拔拉起重机     | 1     |
B     | 138-7575     | 连杆支架     | 3     |
C     | 189-0409     | 钩环组件     | 2     |
D     | 1P-2420     | 变速箱修复台     | 1     |
E     | -     | 顶出螺栓 1/2 - NC 13 × 3 in     |
2     |
开始:
- 卸下分动器。 请参阅解体和组装, "分动器 - 拆卸"。
注: 清洁度是一项重要的因素。 解体步骤开始之前,应彻底清洁部件外部。 这将有助于防止脏污进入内部机构。
注: 为便于安装,在所有管路、所有软管、所有线束组件及所有管上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和有助于防止污染物进入系统。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 使用工具 (A) 、工具 (B) 、工具 (C) 和适当的起吊设备,将变矩器壳体 (1) 安置在工具 (D) 上。 变矩器和变矩器壳体 (1) 的重量约为 590 kg (1300 lb)。
Show/hide table
图 1 | g01289637 |
- 将工具 (B) 连接在变矩器 (2) 上。 变矩器 (2) 的重量约为 365 kg (805 lb)。
Show/hide table
图 2 | g01289639 |
Show/hide table
图 3 | g01289640 |
Show/hide table
图 4 | g01289642 |
- 卸下螺栓 (3) 。
- 使用工具 (E) 、工具 (B) 和适当的起吊设备,从壳体上卸下变矩器 (2) 。
- 卸下 O 形密封圈 (4) 。
Show/hide table
图 5 | g01289643 |
Caterpillar Information System:
C27 and C32 Generator Set Engines Fan Drive - Remove and Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Modulating Valve (Transmission Clutch) - Remove and Install
C11 and C13 Engines Valve Mechanism Cover - Remove and Install
2006/07/01 A New Backup Ring for the Fuel Injector Group is Now Available {1251, 1254, 1290}
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Transfer Gears - Install - Idler
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Transfer Gears - Remove - Idler
C15 On-Highway Engine Valve Mechanism Cover - Remove and Install
3500B Generator Sets Emergency Stopping
C175-16 Locomotive Engine Valve Lash - Adjust
G3500 Engines Flywheel
C15 On-Highway Engine Engine Oil Filter Base - Install
C15 On-Highway Engine Engine Oil Filter Base - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Install
C32 Power Module Heat Shield - Inspect/Replace
C27 and C32 Generator Set Engines Belt Guard - Remove and Install
C27 and C32 Generator Set Engines Fan - Remove and Install
C27 and C32 Generator Set Engines Fan Guard - Remove and Install
C15 On-Highway Engine Valve Mechanism Cover Base - Remove and Install
C32 Power Module Air Inlet Filter - Check
3612 and 3616 Engines Fuel Priming Pump - Remove
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Disassemble
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Assemble
3612 and 3616 Engines Fuel Priming Pump - Install
Caterpillar Logic Control Governor One (LCG1) and Caterpillar Logic Control Governor Two (LCG2){1264, 1908} Caterpillar Logic Control Governor One (LCG1) and Caterpillar Logic Control Governor Two (LCG2){1264, 1908}