Torque Converter - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-2420     | 变速箱修复台     | 1     |
B     | 138-7575     | 连杆支架     | 3     |
C     | -     | 顶出螺栓 1/2 - 13 × 3 in     |
2     |
D     | 126-7183     | 十字挡块     | 1     |
E     | -     | 顶出螺栓 1/2 - 13 × 3 in     |
2     |
F     | 1P-0520     | 冲头总成     | 1     |
G     | 9S-7338     | 十字挡块     | 1     |
H     | 6V-3160     | 双作用油缸     | 1     |
9S-7338 | 十字挡块     | 1     | |
8B-7550 | 推拉支腿     | 2     | |
1B-4207 | 全高螺母     | 2     | |
3H-0465 | 推拉板     | 4     | |
5P-4808 | 盖     | 2     | |
3S-6224 | 电动液压泵总成     | 1     | |
9U-6833 | 螺母     | 1     | |
8S-6587 | 适配器     | 1     | |
4C-9633 | 拉拔器螺柱     | 1     | |
9U-6261 | 轴承拆卸工具适配器     | 1     | |
J     | 140-7742     | 套环     | 2     |
K     | 2P-8312     | 挡圈钳     | 1     |
L     | 276-6863     | 活动扳手组件     | 1     |
M     | 8B-7551     | 轴承拉拔器总成     | 1     |
1P-5546 | 横木     | 1     | |
8B-7549 | 拉拔器腿     | 2     | |
3H-0465 | 推拉板     | 4     | |
1B-4207 | 全高螺母     | 2     | |
1P-0510 | 冲头总成     | 1     | |
5P-8715 | 顶出螺栓     | 1     | |
N.     | 1P-7407     | 吊环螺栓     | 1     |
P     | 8H-0663     | 轴承拉拔器总成     | 1     |
开始:
- 拆下变矩器。 请参阅拆解和组装, "变矩器 - 拆卸"。
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
- 使用工具 (B) 将变矩器 (1) on 定位到工具 (A) 。 变矩器 (1) 的重量约为 340 kg (750 lb)。
Show/hide table
图 1 | g01290107 |
- 拆下螺栓 (2) 。
Show/hide table
图 2 | g01290108 |
Show/hide table
图 3 | g01290109 |
- 使用工具 (C) 拆下先导阀 (3) 。
- 拆下螺栓 (4) 、板 (5) 和垫圈 (6) 。
Show/hide table
图 4 | g01290110 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 拆下螺栓 (8) 。
Show/hide table
图 5 | g01290112 |
- 使用工具 (B) 、工具 (D) 、工具 (E) 和适当的起吊设备拆下托架和涡轮组件 (7) 。 托架和涡轮组件的重量约为 141 kg (310 lb)。
- 重新定位工具 (B) 。 使用工具 (B) 、工具 (D) 和适当的起吊设备翻转托架和涡轮组件 (7) 。
Show/hide table
图 6 | g01290133 |
- 拆下螺栓 (9) 和涡轮 (10) 。
Show/hide table
图 7 | g01290134 |
- 拆下轮毂 (11) 。
Show/hide table
图 8 | g01290135 |
- 使用工具 (F) 和适当的压具将轴承 (12) 从轮毂 (11) 上拆下。
- 拆下螺栓 (13) 、挡圈 (14) 和板 (15) 。
Show/hide table
图 9 | g01290138 |
- 拆下盘 (16) 和板 (17) 。
注: 记下盘 (16) 和板 (17) 的数量和位置以便于组装。
Show/hide table
图 10 | g01290139 |
Show/hide table
图 11 | g01290140 |
- 使用工具 (B) 、工具 (D) 和适当的起吊设备托架组件 (18) 以翻转托架组件 (18) 。 托架组件 (18) 的重量约为 115 kg (250 lb)。
Show/hide table
图 12 | g01290141 |
- 拆下工具 (B) 和工具 (D) 。
- 使用工具 (F) 和工具 (G) 拆下轮毂 (19) 和托架组件 (18) 。
Show/hide table
图 13 | g01290142 |
- 使用工具 (B) 和适当的起吊设备,卸下行星齿轮架组件 (18) 。 托架 (18) 的重量约为 70 kg (150 lb)。
Show/hide table
图 14 | g01290146 |
- 将密封圈 (21) 从活塞 (20) 上拆下。
Show/hide table
图 15 | g01192330 |
- 将座圈 (22) 和托架 (23) 从轮毂 (19) 上拆下。
Show/hide table
图 16 | g01290151 |
- 将密封圈 (24) 从托架 (23) 上拆下。
Show/hide table
图 17 | g01192349 |
- 拆下轴承座圈 (25) 。
Show/hide table
图 18 | g01290158 |
- 安装工具 (H) 后将轴承和套筒 (26) 从托架 (18) 上拆下。
Show/hide table
图 19 | g01290160 |
- 拆下密封圈 (27) 。
Show/hide table
图 20 | g01290162 |
- 拆下座圈 (28) 。
Show/hide table
图 21 | g01192377 |
- 拆下轴承组件 (29) 。
Show/hide table
图 22 | g01192378 |
- 拆下定子组件 (30) 。
注: 拆下定子组件时应小心。
Show/hide table
图 23 | g01192379 |
- 拆下挡圈 (31) 和滑板 (32) 。
Show/hide table
图 24 | g01192426 |
- 拆下滚柱保持架 (36) 。 将自由轮滚柱 (33) 和弹簧 (35) 从滚柱保持架 (36) 上拆下。 将滑板 (37) 和自由轮凸轮 (34) 从定子组件 (30) 上拆下。
Show/hide table
图 25 | g01290168 |
- 将工具 (J) 和适当的起吊设备连接到叶轮组件 (38) 上。
Show/hide table
图 26 | g01290170 |
Show/hide table
图 27 | g01192626 |
Show/hide table
图 28 | g01192604 |
- 拆下轴承 (40) 、座圈 (43) 和套筒 (44) 。
- 拆下螺栓 (39) 、螺栓 (42) 和轮毂 (41) 。
- 使用适当的起吊设备拆下叶轮组件 (38) 。
- 使用工具 (B) 和适当的起吊设备拆下壳体组件 (45) 。 壳体组件 (45) 的重量约为 90 kg (195 lb)。
Show/hide table
图 29 | g01192629 |
- 拆下螺栓 (46) ,然后拆下泵驱动齿轮 (47) 。
Show/hide table
图 30 | g01192634 |
- 使用适当的冲头拆下耐磨套筒 (48) 。
- 使用工具 (K) 拆下挡圈 (49) 。 拆下螺栓 (51) 、对开口垫圈 (52) 和自由轮座圈 (50) 。
Show/hide table
图 31 | g01192639 |
- 使用工具 (B) 和适当的起吊设备重新放置轴组件 (53) 。 轴组件 (53) 的重量约为 79 kg (175 lb)。
Show/hide table
图 32 | g01290176 |
- 拆下螺栓 (54) 和分配器 (55) 。
Show/hide table
图 33 | g01290177 |
- 拆下密封圈 (56) 。
Show/hide table
图 34 | g01746769 |
- 使用工具 (L) 拆下螺母 (57) 。
- 拆下锁紧垫圈 (58) 和转子 (59) 。
- 装上工具 (M) 后拆下托架 (60) 。
Show/hide table
图 35 | g01746674 |
- 将密封圈 (61) 和 (62) 从托架 (60) 上拆下。
Show/hide table
图 36 | g01746975 |
- 使用工具 (N) 和适当的起吊设备将轴组件 (53) 从托架组件 (63) 上拆下。 轴组件 (53) 的重量约为 28 kg (60 lb)。 托架组件 (63) 的重量约为 35 kg (75 lb)。
Show/hide table
图 37 | g01747435 |
- 需要两名人员将轴组件 (53) 放到适当的压具中。 将工具 (F) 放置到轴组件 (53) 上。 使用工具 (P) 和适当的压具拆下轴承 (64) 和密封托架 (65) (图中未显示)。
Show/hide table
图 38 | g01748018 |
- 拆下密封圈 (66) 和 O 形密封圈 (69) 。 使用工具 (K) 拆下挡圈 (67) 。 将轴承 (68) 从托架 (63) 上拆下。
Show/hide table
图 39 | g01748341 |
Caterpillar Information System:
3612 and 3616 Engines Fuel Priming Pump - Remove
C32 Power Module Air Inlet Filter - Check
C15 On-Highway Engine Valve Mechanism Cover Base - Remove and Install
C27 and C32 Generator Set Engines Fan Guard - Remove and Install
C27 and C32 Generator Set Engines Fan - Remove and Install
C27 and C32 Generator Set Engines Belt Guard - Remove and Install
C32 Power Module Heat Shield - Inspect/Replace
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Remove
C27 and C32 Generator Set Engines Fan Drive - Remove and Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Modulating Valve (Transmission Clutch) - Remove and Install
C11 and C13 Engines Valve Mechanism Cover - Remove and Install
TH48-E70 Oil/Gas Transmission and TH48-E70-C27 and TH48-E70-C32 Package Torque Converter - Assemble
3612 and 3616 Engines Fuel Priming Pump - Install
Caterpillar Logic Control Governor One (LCG1) and Caterpillar Logic Control Governor Two (LCG2){1264, 1908} Caterpillar Logic Control Governor One (LCG1) and Caterpillar Logic Control Governor Two (LCG2){1264, 1908}
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C11I, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Power Train Electronic Control System Transmission Control (Shift Solenoid) - Calibrate
2006/08/01 New Oil Pan is Now Available {1302}
C27 and C32 Generator Set Engines Cooling System Package (Radiator, Aftercooler, Fuel Cooler) - Remove
2006/07/24 A New Backup Ring for the Fuel Injector Group is Now Available {1251, 1254, 1290}
2006/07/24 A New Backup Ring for the Fuel Injector Group is Now Available {1251, 1254, 1290}
C27 and C32 Generator Set Engines Cooling System Package (Radiator, Aftercooler, Fuel Cooler) - Install
C175-16 and C175-20 Generator Set Engines Temperature Sensor
C280-12 and C280–16 Marine Engines Fuel Pressure Control Valve - Remove
C280-12 and C280–16 Marine Engines Fuel Pressure Control Valve - Install