Engine Oil Pan - Remove and Install - Aluminum and Pressed Steel Oil Pans
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
Show/hide table
图 1 | g01478088 |
典型示例 |
Show/hide table
图 2 | g01797036 |
典型示例 |
- 在发动机油底壳下面放一个适当的容器。 卸下排放塞 (5),排放发动机机油。 有关正确的步骤,请参阅操作和保养手册, "发动机机油和滤清器 - 更换"。
- 从排放塞 (5 )上卸下 O 形密封圈 (11)。
- 从夹子 ( 6) 上断开通气孔软管 (1)。 将呼吸器软管放置在远离发动机油底壳的地方。
- 如有必要,卸下油尺管组件。 松开螺母 (3),卸下管组件 (2)。 从管组件上拆下密封件 (4)。
注: 确定管组件的位置和朝向。
- 支撑住发动机油底壳组件。 标记夹子 ( 6) 的位置。 拧松螺栓 ( 9) 和螺栓 (10)。 拆除夹子并拆卸螺栓。
- 卸下发动机油底壳 (8),然后从缸体上卸下垫片 (7)。
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导螺栓 (M8 × 100 mm) |
4 |
B | - | Loctite 5900 | - |
C | 4C-4030 | 螺纹锁固胶 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保缸体表面清洁、无损坏。
Show/hide table
图 3 g01251768 典型示例 - 将工具 (A) 安装到缸体中的位置 (X)。
- 确保发动机油底壳清洁且无损坏。
Show/hide table
图 4 g01251763 典型示例 Show/hide table图 5 g01803754 典型示例 - 将一滴工具 ( B) 涂敷在缸体的 ( Y) 处。
注: 如果刚刚安装缸体桥接件,必须在工具 ( B )固化之前安装发动机油底壳。
Show/hide table图 6 g01797036 典型示例 - 将新垫片 (7) 放置在发动机油底壳 ( 8 )上。
- 将发动机油底壳组件与工具 (A) 对准。 将发动机油底壳组件安装到缸体中。 将夹子 ( 6 )安装到位。
- 安装螺栓 (10) 并用手拧紧。
- 拆下工具 (A)。
- 将工具 (C) 涂敷在螺栓 (9) 上。
- 安装螺栓 (9) 和其余的螺栓 (10)。
- 拧紧螺栓 (9) 和螺栓 (10) 至扭矩
22 N·m (16 lb ft) 。 请参阅规格, "发动机油底壳",了解正确的拧紧顺序。Show/hide table图 7 g01478088 典型示例 - 将新的 O 形密封圈安装到排放塞 ( 5 )上。 将排放螺塞安装到发动机油底壳上。 拧紧机油排放塞至扭矩为
34 N·m (25 lb ft) 。 - 如有必要,按照步骤 13.a 至步骤 13.c,安装油尺管组件。
- 将新密封圈 ( 4) 安装到管组件 (2 )上。
- 将工具 ( C) 涂敷在螺母 ( 3) 上。 将管组件安装到发动机油底壳上。
注: 确保管组件的方位正确。
- 拧紧螺母 (3) 至扭矩
18 N·m (13 lb ft) 。 安装油尺。
- 加注发动机油底壳至正确油位。 有关正确的步骤,请参阅操作和保养手册, "发动机机油和滤清器 - 更换"。
Caterpillar Information System:
C15 On-Highway Engine Alternator Mounting
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Cast Iron Oil Pan
C4.4 Industrial Engine Engine Oil Filter Base - Remove and Install
C4.4 Industrial Engine Engine Oil Cooler - Remove
C4.4 Industrial Engine Engine Oil Cooler - Install
C4.4 Industrial Engine Electronic Unit Injector - Install
C4.4 Industrial Engine Electronic Unit Injector - Remove
C4.4 Industrial Engine Electronic Control Module - Remove and Install
C4.4 Industrial Engine Electric Starting Motor - Remove and Install
C4.4 Industrial Engine ECM Mounting Bracket - Remove and Install
C4.4 Industrial Engine Cylinder Head - Remove
C4.4 Industrial Engine Cylinder Head - Install
C4.4 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C4.4 Industrial Engine Engine Oil Pump - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Exhaust Elbow - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C4.4 Industrial Engine Fan - Remove and Install
C4.4 Industrial Engine Fan Drive - Remove and Install
C4.4 Industrial Engine Flywheel - Install
C4.4 Industrial Engine Flywheel - Remove
C4.4 Industrial Engine Flywheel Housing - Remove and Install
C4.4 Industrial Engine Front Cover - Remove and Install