Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-7262 | 伸缩式磁铁 | 1 |
开始:
- 拆下发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拧松盖 (2)。 小心地从平衡器 (1) 上卸下盖。
注: 卸下盖后会释放弹力。
- 从平衡器 (1) 中的安全阀孔上卸下弹簧 (3)。
- 使用工具 (A),从平衡器 (1) 中的安全阀孔上卸下柱塞 (4) 。
Show/hide table
图 1 | g01470291 |
典型实例 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-7262 | 伸缩式磁铁 | 1 |
B | 4C-4030 | 螺纹锁固胶 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。 如果平衡器 (1) 中的安全阀孔磨损或损坏,必须更换整个平衡器组件。
- 使用清洁的发动机机油润滑柱塞 (4)。 将柱塞 (4) 和弹簧 (3) 安装到平衡器 (1) 的安全阀孔中。
注: 柱塞必须能在安全阀孔中自由滑动。
- 将工具 (B) 涂敷在盖 (2) 的螺纹上。 将盖 (2) 安装到平衡器 (1) 上。 拧紧盖至扭矩为
21 N·m (15.5 lb ft) 。注: 确保弹簧正确安装在柱塞上和盖内。 确保工具 (B) 没有污染平衡器 (1) 中的安全阀孔。
Show/hide table
图 2 | g01470291 |
典型实例 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
结束:
- 安装发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
Caterpillar Information System:
C4.4 Industrial Engine Engine Oil Pump - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Aluminum and Pressed Steel Oil Pans
C15 On-Highway Engine Alternator Mounting
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Cast Iron Oil Pan
C4.4 Industrial Engine Engine Oil Filter Base - Remove and Install
C4.4 Industrial Engine Engine Oil Cooler - Remove
C4.4 Industrial Engine Engine Oil Cooler - Install
C4.4 Industrial Engine Electronic Unit Injector - Install
C4.4 Industrial Engine Electronic Unit Injector - Remove
C4.4 Industrial Engine Electronic Control Module - Remove and Install
C4.4 Industrial Engine Electric Starting Motor - Remove and Install
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Exhaust Elbow - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C4.4 Industrial Engine Fan - Remove and Install
C4.4 Industrial Engine Fan Drive - Remove and Install
C4.4 Industrial Engine Flywheel - Install
C4.4 Industrial Engine Flywheel - Remove
C4.4 Industrial Engine Flywheel Housing - Remove and Install
C4.4 Industrial Engine Front Cover - Remove and Install
C4.4 Industrial Engine Fuel Filter Base - Remove and Install - Secondary Fuel Filter
C4.4 Industrial Engine Fuel Injection Lines - Install
C4.4 Industrial Engine Fuel Injection Lines - Remove