Engine Oil Filter Base - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 185-3630 | 带式扳手组件 | 1 |
注: 机油滤清器可垂直或水平安装。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检查, 保养, 测试, 调整 and 维修发动机时,务必留心,确保将溢出的液体盛装在容器中。在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 使用工具 (A),拆下发动机机油滤清器 ( 3)。 请参阅操作和保养手册 , "发动机机油和滤清器 - 更换"。
- 如果发动机机油压力传感器位于发动机机油滤清器底座中,卸下发动机机油压力传感器。 请参阅拆解和组装发动机机油压力传感器 - 拆卸和, "安装" 。
- 卸下螺栓 (4),然后卸下发动机机油滤清器底座 ( 2)。
- 拆下垫片 (1)。
- 如果发动机机油滤清器座配有垫板,卸下该垫板,然后卸下垫片。
注: 标记垫板的方向。
- 如有必要,从发动机机油滤清器底座 ( 2) 上卸下塞 (6)。 从螺塞上拆下 O 形密封圈 ( 5)。
Show/hide table
图 1 | g01254186 |
典型实例 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
B | 4C-4030 | 螺纹锁固胶 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保发动机机油滤清器底座清洁。 清洁缸体表面。
- 如有必要,将新的 O 形密封圈 (5) 安装到塞 ( 6) 上。 将塞 (6) 安装到在发动机机油滤清器座 ( 2) 上。 将塞拧紧至扭矩为
12 N·m (106 lb in) 。 - 将螺栓 (4) 安装到发动机机油滤清器底座 ( 2) 上。
- 将新垫片 (1) 安装到螺栓 ( 4) 上。 如果发动机机油滤清器底座配有垫板,安装该垫板,然后将新垫片安装在螺栓上。
注: 确保垫板的方向正确。
- 将工具 (B) 涂覆到螺栓的螺纹上。 将发动机机油滤清器底座组件安装到缸体上。
- 将螺栓 (4) 拧紧至扭矩
22 N·m (16 lb ft) 。 - 如果发动机机油压力传感器位于发动机机油滤清器底座中,安装发动机机油压力传感器。 请参阅拆解和组装发动机机油压力传感器 - 拆卸和, "安装" 。
- 安装新发动机机油滤清器 ( 3)。 如有必要,加注发动机油底壳至油位表上显示的正确油位。 请参阅操作和保养手册 , "发动机机油和滤清器 - 更换"。
Show/hide table
图 2 | g01254186 |
典型实例 |
Caterpillar Information System:
C4.4 Industrial Engine Engine Oil Cooler - Remove
C4.4 Industrial Engine Engine Oil Cooler - Install
C4.4 Industrial Engine Electronic Unit Injector - Install
C4.4 Industrial Engine Electronic Unit Injector - Remove
C4.4 Industrial Engine Electronic Control Module - Remove and Install
C4.4 Industrial Engine Electric Starting Motor - Remove and Install
C4.4 Industrial Engine ECM Mounting Bracket - Remove and Install
C4.4 Industrial Engine Cylinder Head - Remove
C4.4 Industrial Engine Cylinder Head - Install
C4.4 Industrial Engine Crankshaft Timing Ring - Remove and Install
C4.4 Industrial Engine Crankshaft Rear Seal - Remove
C4.4 Industrial Engine Crankshaft Rear Seal - Install
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Cast Iron Oil Pan
C15 On-Highway Engine Alternator Mounting
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Aluminum and Pressed Steel Oil Pans
C4.4 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C4.4 Industrial Engine Engine Oil Pump - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Exhaust Elbow - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C4.4 Industrial Engine Fan - Remove and Install
C4.4 Industrial Engine Fan Drive - Remove and Install
C4.4 Industrial Engine Flywheel - Install