Crankshaft Timing Ring - Remove and Install
拆卸步骤
开始:
- 拆下曲轴。 请参阅拆解和组装, "曲轴 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将曲轴 (1) 支撑在适当的台架上。
Show/hide table
图 1 | g01254108 |
- 将六角头螺钉 (2) 从曲轴正时齿圈 (3) 上拆下。 不要重复使用六角螺钉。
- 小心地将曲轴正时齿圈 (3) 从曲轴 (1) 上卸下。 不要重复使用曲轴正时齿圈。
注: 拆卸曲轴正时齿圈时,确保不损坏曲轴的密封表面 (4) 。
注: 除非定位销损坏,否则不要将定位销 (5) 从曲轴 (1) 上卸下。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 194-3541     | 4 mm 六角接头     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将曲轴 (1) 支撑在适当的台架上。
- 确保曲轴上曲轴正时齿圈的法兰清洁且无损坏。
- 如果定位销 (5) 已拆下,将新定位销安装到曲轴 (1) 上。
Show/hide table
图 2 | g01254108 |
- 将曲轴正时齿圈 (3) 放置到斗齿朝向密封面 ( 4) 后方的曲轴中。 将曲轴正时齿圈 (3) 的孔与销 ( 5) 对齐。 小心地将曲轴正时齿圈 (3) 安装到曲轴 (1) 上。
注: 安装曲轴正时齿圈时,确保不损坏曲轴的密封表面 (4) 。
- 使用工具 ( A ) 安装新的六角螺钉 ( 2) 。 拧紧六角头螺钉至扭矩为 15 N·m (133 lb in)。
End By: 安装曲轴。 请参阅 拆解和组装, "曲轴 - 安装"。
Caterpillar Information System:
C4.4 Industrial Engine Crankshaft Rear Seal - Remove
C4.4 Industrial Engine Crankshaft Rear Seal - Install
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Crankshaft Position Sensor - Remove and Install
C4.4 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C4.4 Industrial Engine Crankshaft Gear - Remove and Install
C4.4 Industrial Engine Crankshaft Front Seal - Remove and Install
C4.4 Industrial Engine Crankshaft - Remove
C4.4 Industrial Engine Crankshaft - Install
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Unfiltered Breather
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Filtered Breather
C4.4 Industrial Engine Cylinder Head - Install
C4.4 Industrial Engine Cylinder Head - Remove
C4.4 Industrial Engine ECM Mounting Bracket - Remove and Install
C4.4 Industrial Engine Electric Starting Motor - Remove and Install
C4.4 Industrial Engine Electronic Control Module - Remove and Install
C4.4 Industrial Engine Electronic Unit Injector - Remove
C4.4 Industrial Engine Electronic Unit Injector - Install
C4.4 Industrial Engine Engine Oil Cooler - Install
C4.4 Industrial Engine Engine Oil Cooler - Remove
C4.4 Industrial Engine Engine Oil Filter Base - Remove and Install
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Cast Iron Oil Pan
C15 On-Highway Engine Alternator Mounting