Engine Oil Cooler - Remove
开始:
- 卸下电子控制模块的支架。 请参阅拆解和组装 , "ECM 安装支架 - 拆卸和安装" 。
Show/hide table
注意 |
---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前,请参阅 操作和保养手册 , "一般危险信息和高压燃油管路 "以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息,请参阅 系统操作、测试和调整手册 , "燃油系统部件清洁度 "。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 从冷却系统将冷却液排入合适的容器中。 有关正确的步骤,请参阅 操作和保养手册 , "冷却系统冷却液 - 更换"。
- 将发动机润滑机油排入合适的容器中。 有关正确的步骤,请参阅 操作和保养手册 , "发动机机油和滤清器 - 更换"。
- 如有必要,卸下电动起动马达。 请参阅拆解和组装 , "电起动马达 - 拆卸和安装" 。
- 将发动机配线线束置放在远离机油冷却器 ( 1) 组件的位置上。 如有必要,切断电缆扎带。
Show/hide table
图 1 g01254472 典型实例 Show/hide table图 2 g01254473 发动机机油冷却器的拧紧顺序 - 如图 2 所示数字从大到小的顺序松开螺栓 ( 7)。. 拆下螺栓 (7)。 在卸下螺栓的过程中,支撑起发动机机油冷却器 ( 1) 的组件。
注: 安装不同长度的螺栓。 记录螺栓的正确位置。 记录由螺栓固定的所有支架的位置。 此时请勿卸下螺栓 ( 6)。
- 从缸体上卸下机油冷却器 ( 1) 的组件。
- 卸下垫片 (2)。
- 按照步骤 8.a 至步骤 8.c 以拆解发动机机油冷却器。
- 拆下螺栓 (6)。
- 从壳体 (5) 上卸下冷却器模具 ( 3)。
- 拆下垫片 (4)。
Caterpillar Information System:
C4.4 Industrial Engine Engine Oil Cooler - Install
C4.4 Industrial Engine Electronic Unit Injector - Install
C4.4 Industrial Engine Electronic Unit Injector - Remove
C4.4 Industrial Engine Electronic Control Module - Remove and Install
C4.4 Industrial Engine Electric Starting Motor - Remove and Install
C4.4 Industrial Engine ECM Mounting Bracket - Remove and Install
C4.4 Industrial Engine Cylinder Head - Remove
C4.4 Industrial Engine Cylinder Head - Install
C4.4 Industrial Engine Crankshaft Timing Ring - Remove and Install
C4.4 Industrial Engine Crankshaft Rear Seal - Remove
C4.4 Industrial Engine Crankshaft Rear Seal - Install
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Engine Oil Filter Base - Remove and Install
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Cast Iron Oil Pan
C15 On-Highway Engine Alternator Mounting
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Aluminum and Pressed Steel Oil Pans
C4.4 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C4.4 Industrial Engine Engine Oil Pump - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Exhaust Elbow - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C4.4 Industrial Engine Fan - Remove and Install
C4.4 Industrial Engine Fan Drive - Remove and Install