Engine Oil Cooler - Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 按照步骤 1.a 至步骤 1.c 组装发动机机油冷却器。
- 确保冷却器模具 ( 3) 清洁且无损坏。 确保壳体 (5) 清洁且无损坏。 更换任何损坏的部件。
- 将新垫片 (4) 装至壳体 ( 5) 上。 安装冷却器模具 ( 3)。
- 安装螺栓 (6) 并用手拧紧。
- 清洁缸体表面。
- 安装螺栓 (7) 至发动机机油冷却器。
注: 每个螺栓的长度不同。 确保不同螺栓的安装位置正确。 确保将所有由螺栓固定的支架安装在正确位置。
- 安装新的垫片 (2) 至机油冷却器 ( 1)的组件。 将螺栓 ( 7) 推进垫片的孔。
注: 垫片中的孔有固定螺栓的锯齿。
Show/hide table图 2 g01254473 发动机机油冷却器的拧紧顺序 - 安装机油冷却器 ( 1) 的组件至缸体。 拧紧螺栓 (7) 至扭矩为
22 N·m (16 lb ft) 。 按照图 2 中所示的顺序拧紧螺栓。拧紧螺栓 (6) 至扭矩为
22 N·m (16 lb ft) 。 请参阅插图 1。 - 将发动机配线线束放置在正确的位置上。 如有必要,安装新的电缆扎带。
- 如有必要,安装电动起动马达。 请参阅拆解和组装 , "电起动马达 - 拆卸和安装" 。
- 加注冷却系统至正确液位。 有关正确的步骤,请参阅 操作和保养手册 , "冷却系统冷却液 - 更换"。
- 加注发动机油底壳至正确油位。 有关正确的步骤,请参阅 操作和保养手册 , "发动机机油和滤清器 - 更换"。
Show/hide table
图 1 | g01254472 |
典型实例 |
结束:
- 安装电子控制模块的支架。 请参阅拆解和组装 ECM, "支架 - 拆卸和安装"。
Caterpillar Information System:
C4.4 Industrial Engine Electronic Unit Injector - Install
C4.4 Industrial Engine Electronic Unit Injector - Remove
C4.4 Industrial Engine Electronic Control Module - Remove and Install
C4.4 Industrial Engine Electric Starting Motor - Remove and Install
C4.4 Industrial Engine ECM Mounting Bracket - Remove and Install
C4.4 Industrial Engine Cylinder Head - Remove
C4.4 Industrial Engine Cylinder Head - Install
C4.4 Industrial Engine Crankshaft Timing Ring - Remove and Install
C4.4 Industrial Engine Crankshaft Rear Seal - Remove
C4.4 Industrial Engine Crankshaft Rear Seal - Install
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Engine Oil Cooler - Remove
C4.4 Industrial Engine Engine Oil Filter Base - Remove and Install
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Cast Iron Oil Pan
C15 On-Highway Engine Alternator Mounting
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Aluminum and Pressed Steel Oil Pans
C4.4 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C4.4 Industrial Engine Engine Oil Pump - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Exhaust Elbow - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C4.4 Industrial Engine Fan - Remove and Install