Cylinder Head - Remove
开始:
- 拆下排气歧管。 请参阅拆解和组装 , "排气歧管 - 拆卸和安装 "。
- 拆下燃油歧管。 请参阅拆解和组装 , "燃油歧管(油轨)- 拆卸和安装"。
- 卸下电子控制模块的安装支架。 请参阅拆解和组装 , "ECM 安装支架 - 拆卸和安装" 。
- 拆下电子单体喷油器。 请参阅拆解和组装 , "电子单体喷油器 - 拆卸"。
- 拆下气门机构罩盖底座。 请参阅拆解和组装 , "气门机构罩盖底座 - 拆卸和安装" 。
- 卸下预热塞。 请参阅 拆解和组装, "电热塞 - 拆卸和安装 "。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
注: 为便于安装,在所有软管、软管组件、导线及管组件上做出识别标记。 塞住所有软管组件和管组件。 这将有助于防止液体泄漏和防止污染物进入系统。
- 如果交流发电机支架安装在缸盖上,则卸下交流发电机。 请参阅拆解和组装 , "交流发电机 - 拆卸"。
- 如果燃油注油泵和燃油粗滤器都安装在缸盖上,则卸下燃油注油泵和燃油粗滤器。 请参阅拆解和组装 , "燃油注油泵 - 拆卸和安装" 。
- 将冷却液从冷却系统中排入合适的容器,以便保存或弃置。 关于正确的排放步骤,请参阅 操作和保养手册 , "冷却系统冷却液 - 更换"。
Show/hide table
图 1 g01245537 典型实例 - 从水温调节器壳体 ( 1) 上断开散热器上软管。
- 如有必要,从进气连接上卸下空气软管。
- 按照步骤 6.a 和步骤 6.b,将线束组件 ( 4) 和冷却液温度传感器 ( 2) 断开。
- 滑动锁扣至解锁位置。
- 将线束组件 (4) 和冷却液温度传感器 ( 2) 断开。
- 如有必要,按照步骤 7.a 和步骤 7.b,将线束组件 ( 4) 和增压压力传感器 ( 3) 断开。
- 滑动锁扣至解锁位置。
- 将线束组件 (4) 和增压压力传感器 ( 3) 断开。
Show/hide table图 2 g01249835 典型实例 - 按照步骤 8.a 和步骤 8.b,将线束组件 ( 4) 和进气温度传感器 ( 5) 断开。
- 滑动锁扣至解锁位置。
- 将线束组件 (4) 与进气温度传感器 ( 5) 断开。
- 卸下固定线束组件 ( 4) 到缸盖的所有电缆扎带。 卸下缸盖期间,为了避免造成阻塞,应将线束组件固定。
Show/hide table
图 3 g01249474 典型实例 - 从缸盖和输油泵 ( 7) 卸下管组件 (6)。
Show/hide table
图 4 g01249479 典型实例 - 如果发动机配备废气旁通阀,则将线束组件 ( 9) 从管组件 (8) 卸下。 卸下管夹 (10) 和管夹 ( 11) 的螺栓。 将管组件 ( 8) 从废气旁通阀和缸盖上卸下。
Show/hide table
图 5 g01476537 典型实例 - 拆下螺栓 (12)。 记录由螺栓固定的所有支架的位置。 从缸盖上卸下旁通管 ( 13)。 从旁通管上卸下 O 形密封圈 (14) 和 ( 15)。
Show/hide table
图 6 g01245538 Show/hide table图 7 g01250785 松开缸盖螺栓的顺序 - 如图 7 所示数字从大到小的顺序逐步松开螺栓 ( 16)。
注: 遵循正确的顺序有助于防止缸盖失真。
- 从缸盖 (17) 上卸下螺栓 ( 16)。
- 将适当的起吊设备连接到缸盖 ( 17)。 支撑缸盖的重量。 缸盖的重量约为
56 kg (124 lb) 。 - 使用适当的起吊设备,小心地从缸体上吊起缸盖 ( 17)。
注: 不要使用操纵杆分离缸盖与缸体。 在拆卸步骤中,小心不要损坏缸盖的加工表面。
Show/hide table注意 将缸盖放在不会使缸盖表面产生擦伤的表面上。
Show/hide table图 8 g01763153 典型实例 - 拆下缸盖垫片 (19)。
- 记录定位销 (18) 在缸体中的位置。 除非定位销损坏,否则不要卸下定位销。
Show/hide table
图 9 g01763173 典型实例 - 如有必要,卸下螺钉 ( 20),然后从缸盖上卸下安装支架 ( 21)。
- 如有必要,从缸盖上卸下水温调节器。 请参阅拆解和组装 , "水温调节器 - 拆卸和安装" 。
- 如有必要,从缸盖上卸下电子传感器。 请参阅拆解和组装 , "冷却液温度传感器 - 拆卸和安装" 。 请参阅拆解和组装 , "空气温度传感器 - 拆卸和安装" 。 请参阅拆解和组装 , "增压压力传感器 - 拆卸和安装" 。
Caterpillar Information System:
C4.4 Industrial Engine Cylinder Head - Install
C4.4 Industrial Engine Crankshaft Timing Ring - Remove and Install
C4.4 Industrial Engine Crankshaft Rear Seal - Remove
C4.4 Industrial Engine Crankshaft Rear Seal - Install
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Crankshaft Position Sensor - Remove and Install
C4.4 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C4.4 Industrial Engine Crankshaft Gear - Remove and Install
C4.4 Industrial Engine Crankshaft Front Seal - Remove and Install
C4.4 Industrial Engine Crankshaft - Remove
C4.4 Industrial Engine Crankshaft - Install
C4.4 Industrial Engine ECM Mounting Bracket - Remove and Install
C4.4 Industrial Engine Electric Starting Motor - Remove and Install
C4.4 Industrial Engine Electronic Control Module - Remove and Install
C4.4 Industrial Engine Electronic Unit Injector - Remove
C4.4 Industrial Engine Electronic Unit Injector - Install
C4.4 Industrial Engine Engine Oil Cooler - Install
C4.4 Industrial Engine Engine Oil Cooler - Remove
C4.4 Industrial Engine Engine Oil Filter Base - Remove and Install
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Cast Iron Oil Pan
C15 On-Highway Engine Alternator Mounting
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Aluminum and Pressed Steel Oil Pans
C4.4 Industrial Engine Engine Oil Pressure Sensor - Remove and Install