Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-7262 | 伸缩磁铁 | 1 |
开始:
- 拆下发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 1 | g01470289 |
典型实例 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 卸下螺栓 (6) 和吸入管 (7)。
- 从吸入管上卸下垫片 (5)(未显示)。
- 拧松盖 (2)。 小心地从发动机机油泵 (1) 的壳体上卸下盖 (2)。
注: 卸下盖后会释放弹力。
- 从发动机机油泵 (1) 的壳体中的安全阀孔上卸下弹簧 (4)。
- 使用工具 (A),从发动机机油泵 (1) 的壳体中的安全阀孔上卸下柱塞 (3)。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 2 | g01470289 |
典型实例 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。 如果发动机机油泵 (1) 的壳体中的安全阀孔磨损或损坏,必须更换整个发动机机油泵组件。
- 使用清洁的发动机机油润滑柱塞 (3)。 使用尖嘴钳,将柱塞 (3) 和弹簧 (4) 安装到发动机机油泵 (1) 的壳体中的安全阀孔中。
注: 柱塞必须能在安全阀孔中自由滑动。
- 将盖 (2) 安装到发动机机油泵 (1) 上。 拧紧盖至扭矩为
45 N·m (33 lb ft) 。注: 确保弹簧正确安装在柱塞上和盖内。
- 安装吸入管 (7)和一个新垫片 (5)(未显示)到发动机机油泵的组件上。
- 安装螺栓 (6)。 将螺栓拧紧至扭矩
22 N·m (16 lb ft) 。
结束:
- 安装发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
Caterpillar Information System:
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C4.4 Industrial Engine Engine Oil Pump - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Aluminum and Pressed Steel Oil Pans
C15 On-Highway Engine Alternator Mounting
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Cast Iron Oil Pan
C4.4 Industrial Engine Engine Oil Filter Base - Remove and Install
C4.4 Industrial Engine Engine Oil Cooler - Remove
C4.4 Industrial Engine Engine Oil Cooler - Install
C4.4 Industrial Engine Electronic Unit Injector - Install
C4.4 Industrial Engine Electronic Unit Injector - Remove
C4.4 Industrial Engine Electronic Control Module - Remove and Install
C4.4 Industrial Engine Exhaust Elbow - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C4.4 Industrial Engine Fan - Remove and Install
C4.4 Industrial Engine Fan Drive - Remove and Install
C4.4 Industrial Engine Flywheel - Install
C4.4 Industrial Engine Flywheel - Remove
C4.4 Industrial Engine Flywheel Housing - Remove and Install
C4.4 Industrial Engine Front Cover - Remove and Install
C4.4 Industrial Engine Fuel Filter Base - Remove and Install - Secondary Fuel Filter
C4.4 Industrial Engine Fuel Injection Lines - Install
C4.4 Industrial Engine Fuel Injection Lines - Remove
C4.4 Industrial Engine Fuel Injection Pump - Install