Flywheel Housing - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导螺柱 M10 by 100 mm |
2 |
开始:
- 拆下飞轮。 请参阅拆解和组装, "飞轮 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 从飞轮壳 (1) 的位置 (X) 卸下螺栓。
- 将工具 (A) 安装进飞轮壳 (1) 的位置 (X)。
- 将适当的起吊设备安装到飞轮壳上以支撑飞轮壳。 飞轮壳的重量约为
30 kg (66 lb) 。Show/hide table图 2 g01763013 典型实例 - 从飞轮壳 (1) 上卸下螺栓 (2) 和螺栓 (3)。
- 使用起吊设备,从缸体上卸下飞轮壳 (1)。
Show/hide table
图 3 g01470418 典型实例 - 如果发动机配备铝油底壳,则卸下防尘密封 (5)。
- 如有必要,从缸体上卸下定位销 (4)。
Show/hide table
图 1 | g01470403 |
典型实例 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导螺柱 M10 by 100 mm |
2 |
B | 8T-5096 | 千分表总成 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保飞轮壳清洁、无损坏。 如有必要,更换飞轮壳。
Show/hide table
图 4 g01244056 典型实例 - 检查曲轴后密封 (6) 是否泄漏。 如果观察到漏油,更换曲轴后油封。 请参阅拆解和组装, "曲轴后密封 - 拆除"和拆解和组装, "曲轴后密封 - 安装"。
- 清洁缸体背面。 如有必要,将定位销 (4) 安装到缸体上。
- 将工具 (A) 安装到缸体上。
- 安装防尘密封 (5)。
Show/hide table
图 5 g01763034 典型实例 - 将适当的起吊设备安装到飞轮壳上。 飞轮壳的重量约为
30 kg (66 lb) 。 - 使用起吊设备将飞轮壳 (1) 与工具 (A) 对齐。 将飞轮壳安装到缸体上。
- 安装螺栓 (2) 和螺栓 (3),用手拧紧。
- 拆下工具 (A)。 安装其余的螺栓 (3)。
- 拧紧螺栓 (3) 至扭矩为
63 N·m (46 lb ft) 。 - 拧紧螺栓 (2) 至扭矩为
75 N·m (55 lb ft) 。 - 使用工具 (B),检查飞轮壳与曲轴的对齐情况。 请参阅系统操作、测试和调整, "飞轮壳 - 检查"。
结束:
- 安装飞轮。 请参阅拆解和组装, "飞轮 - 安装"。
Caterpillar Information System:
C4.4 Industrial Engine Flywheel - Remove
C4.4 Industrial Engine Flywheel - Install
C4.4 Industrial Engine Fan Drive - Remove and Install
C4.4 Industrial Engine Fan - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C4.4 Industrial Engine Exhaust Elbow - Remove and Install
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C4.4 Industrial Engine Engine Oil Pump - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Aluminum and Pressed Steel Oil Pans
C15 On-Highway Engine Alternator Mounting
C4.4 Industrial Engine Front Cover - Remove and Install
C4.4 Industrial Engine Fuel Filter Base - Remove and Install - Secondary Fuel Filter
C4.4 Industrial Engine Fuel Injection Lines - Install
C4.4 Industrial Engine Fuel Injection Lines - Remove
C4.4 Industrial Engine Fuel Injection Pump - Install
C4.4 Industrial Engine Fuel Injection Pump - Remove
C4.4 Industrial Engine Fuel Injection Pump Gear - Install
C4.4 Industrial Engine Fuel Injection Pump Gear - Remove
C4.4 Industrial Engine Fuel Manifold (Rail) - Remove and Install
C4.4 Industrial Engine Fuel Pressure Sensor - Remove and Install
C4.4 Industrial Engine Fuel Priming Pump - Remove and Install - Manual Priming Pump
C4.4 Industrial Engine Fuel Transfer Pump - Install