Flywheel - Remove
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导螺栓 1/2 inch - 20 UNF * 4 inch |
2 |
开始:
- 拆下电起动马达。 请参阅拆解和组装, "电起动马达 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 从飞轮 (1) 上的位置 (X) 处卸下两个螺栓。
- 将工具 (A) 安装到飞轮 (1) 上的位置 (X) 处。
- 将适当的起吊设备连接到飞轮 (1) 上。 支撑飞轮的重量。 飞轮的重量约为
71 kg (155 lb) 。 - 拆下其余的螺栓 (2)。
- 使用起吊设备,从发动机上卸下飞轮。
Show/hide table
图 2 g01245152 典型实例 - 检查飞轮 (1) 和齿轮 (3) 是否磨损或损坏。 更换任何损坏或磨损的部件。
- 要卸下飞轮齿圈,请按照步骤 7.a 和步骤 7.b。
- 将飞轮组件放在适当的支架上。
注: 确定飞轮齿圈上齿的方向。
- 使用锤子和冲头以将齿圈 (3) 从飞轮 (1) 上拆下。
- 将飞轮组件放在适当的支架上。
Show/hide table
图 1 | g01245126 |
典型实例 |
Caterpillar Information System:
C4.4 Industrial Engine Flywheel - Install
C4.4 Industrial Engine Fan Drive - Remove and Install
C4.4 Industrial Engine Fan - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C4.4 Industrial Engine Exhaust Elbow - Remove and Install
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C4.4 Industrial Engine Engine Oil Pump - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Aluminum and Pressed Steel Oil Pans
C15 On-Highway Engine Alternator Mounting
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Cast Iron Oil Pan
C4.4 Industrial Engine Flywheel Housing - Remove and Install
C4.4 Industrial Engine Front Cover - Remove and Install
C4.4 Industrial Engine Fuel Filter Base - Remove and Install - Secondary Fuel Filter
C4.4 Industrial Engine Fuel Injection Lines - Install
C4.4 Industrial Engine Fuel Injection Lines - Remove
C4.4 Industrial Engine Fuel Injection Pump - Install
C4.4 Industrial Engine Fuel Injection Pump - Remove
C4.4 Industrial Engine Fuel Injection Pump Gear - Install
C4.4 Industrial Engine Fuel Injection Pump Gear - Remove
C4.4 Industrial Engine Fuel Manifold (Rail) - Remove and Install
C4.4 Industrial Engine Fuel Pressure Sensor - Remove and Install
C4.4 Industrial Engine Fuel Priming Pump - Remove and Install - Manual Priming Pump