Flywheel - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导螺栓 1/2 inch - 20 UNF * 4 inch |
2 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 如果已卸下飞轮齿圈,遵循步骤 1.a 至步骤 1.c 以将新齿圈安装到飞轮上。
- 确定新齿圈 (3) 上齿 (4) 的方向。
注: 在安装飞轮时齿圈轮齿的倒角侧必须朝向起动马达。 这将确保起动马达的正确接合。
- 在安装之前,先在烤箱中加热飞轮齿圈 (3) 至最高温度
250 °C (482 °F) 。注: 不要使用喷枪加热齿圈。
- 确保齿圈 (3) 的方向正确,并迅速将齿圈安装到飞轮 (1) 上。
- 确定新齿圈 (3) 上齿 (4) 的方向。
- 检查曲轴后油封是否泄漏。 如果观察到漏油,更换曲轴后油封。 请参阅拆解和组装, "曲轴后密封-拆卸"和拆解和组装, "曲轴后密封-安装"了解正确的步骤。
Show/hide table
图 2 g01245126 典型实例 - 将适当的起吊设备安装到飞轮 (1) 上。 飞轮的重量约为
71 kg (155 lb) 。 - 将工具 (A) 安装到曲轴上的部位 (X) 处。
- 使用起吊设备,将飞轮 (1) 放置在工具 (A) 上。
- 将螺栓 (2) 安装到飞轮 (1) 上,用手拧紧。
- 卸下工具 (A),将剩余的螺栓 (2) 安装到飞轮 (1) 上。
- 从飞轮 (1) 上卸下起吊设备。
- 使用适当的工具,使飞轮不旋转。 拧紧螺栓 (2) 至扭矩
115 N·m (85 lb ft) 。 - 检查飞轮的跳动。 更多信息请参阅技术规格, "飞轮"。
Show/hide table
图 1 | g01470362 |
典型实例 |
Show/hide table
操作已经加热的零件时要坚持戴防护手套。 |
结束:
- 安装电起动马达。 请参阅拆解和组装, "电起动马达 - 拆卸和安装"。
Caterpillar Information System:
C4.4 Industrial Engine Fan Drive - Remove and Install
C4.4 Industrial Engine Fan - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C4.4 Industrial Engine Exhaust Elbow - Remove and Install
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C4.4 Industrial Engine Engine Oil Pump - Remove and Install - Engines Without a Balancer Unit
C4.4 Industrial Engine Engine Oil Pressure Sensor - Remove and Install
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Aluminum and Pressed Steel Oil Pans
C15 On-Highway Engine Alternator Mounting
C4.4 Industrial Engine Engine Oil Pan - Remove and Install - Cast Iron Oil Pan
C4.4 Industrial Engine Engine Oil Filter Base - Remove and Install
C4.4 Industrial Engine Flywheel - Remove
C4.4 Industrial Engine Flywheel Housing - Remove and Install
C4.4 Industrial Engine Front Cover - Remove and Install
C4.4 Industrial Engine Fuel Filter Base - Remove and Install - Secondary Fuel Filter
C4.4 Industrial Engine Fuel Injection Lines - Install
C4.4 Industrial Engine Fuel Injection Lines - Remove
C4.4 Industrial Engine Fuel Injection Pump - Install
C4.4 Industrial Engine Fuel Injection Pump - Remove
C4.4 Industrial Engine Fuel Injection Pump Gear - Install
C4.4 Industrial Engine Fuel Injection Pump Gear - Remove
C4.4 Industrial Engine Fuel Manifold (Rail) - Remove and Install
C4.4 Industrial Engine Fuel Pressure Sensor - Remove and Install