Crankcase Breather - Remove and Install - Filtered Breather
Show/hide table
注意 |
---|
在检查, 保养, 测试, 调整 and 维修发动机时,务必留心,确保将溢出的液体盛装在容器中。在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 卸下滤筒 (8)。 请参阅操作和保养手册, "曲轴箱通气孔(滤筒)- 更换"。
- 松开卡箍 (6),然后卸下软管 (7)。
- 松开弹性卡箍 (2),以便卸下软管 (3)。 从阀机构罩盖的接头 (1) 和滤清器底座 (4) 卸下软管。
- 卸下螺栓 (5),然后卸下滤清器底座 (4)。
注: 如果滤清器底座与发动机之间已安装垫片,则卸下垫片。
Show/hide table图 2 g01903114 - 如有必要,使用合适的工具将接头 (9) 从滤清器底座 (4) 卸下。
Show/hide table
图 1 | g01475258 |
典型实例 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 4C-4030 | 螺纹锁固胶 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保曲轴箱通气孔的所有部件清洁、无损坏。 更换所有损坏的部件。
Show/hide table
图 3 g01903114 - 如有必要,将接头 (9) 安装到滤清器底座 (4) 上。 按照步骤 2.a 至步骤 2.c,将接头 (9) 安装到滤清器底座 (4) 上。
- 将一滴工具 (A) 涂敷在接头 (9) 的螺纹上。
- 将接头 (9) 安装到滤清器底座 (4) 上。
- 拧紧接头 (9) 至扭矩
50 N·m (37 lb ft) 。
Show/hide table图 4 g01475258 典型实例 - 将螺栓 (5) 安装到滤清器底座 (4) 上。
注: 如果已安装垫片,则将垫片放在螺栓上。
- 将滤清器底座组件安装到发动机上。
- 拧紧螺栓 (5) 至扭矩
22 N·m (16 lb ft) 。 - 将弹性卡箍 (2) 安装到软管 (3) 上。 将软管 (3) 安装到阀机构罩盖上的接头 (1) 及滤清器底座 (4) 上。
注: 确保弹性卡箍的位置正确,以便固定软管。
- 将弹性卡箍 (6) 安装到软管 (7) 上。 将软管 (7) 安装到滤清器底座 (4) 上。 牢固地拧紧卡箍。
- 将新滤筒 (8) 安装到滤清器底座 (4) 上。 请参阅操作和保养手册, "曲轴箱通气孔(滤筒)- 更换"。
Caterpillar Information System:
C4.4 Industrial Engine Coolant Temperature Sensor - Remove and Install
C4.4 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C4.4 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C4.4 Industrial Engine Camshaft Gear - Remove and Install
C4.4 Industrial Engine Camshaft Bearings - Remove and Install
C4.4 Industrial Engine Camshaft - Remove and Install
C4.4 Industrial Engine Boost Pressure Sensor - Remove and Install
C4.4 Industrial Engine Balancer - Remove
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove
C4.4 Industrial Engine Balancer - Install
C4.4 Industrial Engine Alternator Belt - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Unfiltered Breather
C4.4 Industrial Engine Crankshaft - Install
C4.4 Industrial Engine Crankshaft - Remove
C4.4 Industrial Engine Crankshaft Front Seal - Remove and Install
C4.4 Industrial Engine Crankshaft Gear - Remove and Install
C4.4 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C4.4 Industrial Engine Crankshaft Position Sensor - Remove and Install
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Crankshaft Rear Seal - Install
C4.4 Industrial Engine Crankshaft Rear Seal - Remove
C4.4 Industrial Engine Crankshaft Timing Ring - Remove and Install