Connecting Rod Bearings - Remove - Connecting rods in position
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A(1) | 9U-6198 | 曲轴转动工具 | 1 |
A(2) | 9U-7336 | 壳体 | 1 |
5P-7305 | 发动机盘车工具 | 1 |
Show/hide table
(1) | 曲轴转动工具用于前皮带轮上。 |
(2) | 此工具用于电动起动马达的孔径中。 |
开始:
- 如果发动机配备平衡器,则卸下该平衡器。 请参阅拆解和装配 , "平衡器 - 拆卸 "。 如果发动机未配备平衡器,则卸下发动机机油泵。 请参阅拆解和组装 , "发动机机油泵 - 拆卸和安装" 。
注: 可以使用两个工具 ( A) 中任意的一个。 请使用最适用的工具。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
弃置所有旧连杆螺栓。 |
注: 如果需要更换所有连杆轴承,可以在两个气缸上同时进行本程序。 本程序可在下列气缸配对上同时进行。 1 和 4 和 2 和 3 。 在将一对气缸更换为另一对气缸前,确保安装了两对连杆轴承。 请参阅拆解和组装 , "连杆轴承 - 安装 "。
- 使用工具 (A) 转动曲轴直到曲轴销处于下死点位置。
如有必要,卸下电热塞。 请参阅拆解和组装 , "电热塞 - 拆卸和安装 "。
注: 拆卸电热塞有助于卸下连杆轴承。 这个操作不是必需的。
Show/hide table图 1 g01479383 Show/hide table图 2 g01253101 - 连杆和连杆盖侧面应有浸蚀编号 ( X)。 连杆和连杆盖上的编号必须相匹配。 如有必要,在连杆 ( 5) 和连杆盖 (2) 上做出一个临时的标记来识别缸号。
注: 不要在断裂口连杆上打出识别标记。 不要在断裂口连杆上打出识别标记。
- 从连杆 (5) 上卸下螺栓 ( 1) 和连杆盖 (2)。 废弃螺栓。
- 从连杆盖 (2) 上拆下连杆轴承 ( 3) 的下半部分。 保持连杆轴承与连杆盖一体。
- 小心地将活塞和连杆组件推入缸孔中,使连杆 ( 5) 不接触曲轴。 从连杆 ( 5) 上拆下连杆轴承 ( 4)的上半部分。 保持轴承一体。
注: 不要按压连杆的断裂口表面,否则会导致损坏。 不要使连杆接触活塞冷却喷嘴。
放置断裂口连杆时必须要安装连杆盖。 在完成连杆轴承的拆卸步骤后,立即进行安装步骤。 请参阅拆解和组装 , "连杆轴承 - 安装"。
Caterpillar Information System:
C4.4 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C4.4 Industrial Engine Camshaft Gear - Remove and Install
C4.4 Industrial Engine Camshaft Bearings - Remove and Install
C4.4 Industrial Engine Camshaft - Remove and Install
C4.4 Industrial Engine Boost Pressure Sensor - Remove and Install
C4.4 Industrial Engine Balancer - Remove
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove
C4.4 Industrial Engine Balancer - Install
C4.4 Industrial Engine Alternator Belt - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Coolant Temperature Sensor - Remove and Install
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Filtered Breather
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Unfiltered Breather
C4.4 Industrial Engine Crankshaft - Install
C4.4 Industrial Engine Crankshaft - Remove
C4.4 Industrial Engine Crankshaft Front Seal - Remove and Install
C4.4 Industrial Engine Crankshaft Gear - Remove and Install
C4.4 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C4.4 Industrial Engine Crankshaft Position Sensor - Remove and Install
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Crankshaft Rear Seal - Install