Connecting Rod Bearings - Install - Connecting rods in position
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A(1) | 9U-6198 | 曲轴转动工具 | 1 |
A(2) | 9U-7336 | 壳体 | 1 |
5P-7305 | 发动机盘车工具 | 1 | |
B | 8T-3052 | 度数轮 | 1 |
C | 383-1654 | 隔套 | 1 |
Show/hide table
(1) | 曲轴转动工具用于前皮带轮。 |
(2) | 该工具在电动起动马达的孔上使用。 |
注: 可以使用两个工具 (A) 中的任意一个。 请使用最适用的工具。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
弃置所有旧连杆螺栓。 |
- 检查曲轴销有无损坏。 如有曲轴损坏,更换曲轴或修复曲轴。 请参阅拆解和组装, "曲轴 - 拆卸"和拆解和组装, "曲轴 - 安装"。 确保连杆轴承清洁、无磨损或损坏。 如有必要,更换连杆轴承。
Show/hide table
图 1 g01260354 Show/hide table图 2 g01001160 在连杆中心对准轴承 - 清洁连杆 (2)。 将工具 (C) 安置于连杆 (5) 上。
- 将连杆轴承 (4) 上轴瓦安装到连杆 (5) 上。 确保上轴瓦在连杆的中心位置。 参考图 2。 拆下工具 (C)。
上轴瓦的两端必须在连杆的中心位置。 上轴瓦的两端与连杆端面的距离必须相等。
- 清洁连杆盖 (2)。 将工具 (C) 安置于连杆盖 (2) 上。
- 将连杆轴承 (3) 下轴瓦安装到连杆盖 (2) 上。 确保连杆轴承在连杆盖的中心位置。 参考图 2。 拆下工具 (C)。
连杆下轴瓦的两端必须在连杆盖的中心位置。 连杆下轴瓦的两端与连杆盖端面的距离必须相等。
- 使用清洁的发动机机油润滑连杆上轴瓦 (4)。
- 如有必要,使用工具 (A),转动曲轴,使曲柄销处于下止点位置。
- 小心地拉动连杆 (5),使其抵到曲轴销上。
注: 不要使连杆接触活塞冷却喷嘴。
- 使用清洁的发动机机油润滑曲柄销和连杆轴承下轴瓦 (3)。
Show/hide table
图 3 g01479452 典型示例 - 将连杆盖 (2) 安装到连杆 (5) 上。
注: 确保连杆盖 (2) 上的蚀刻编号 (X) 与连杆 (5) 上的蚀刻编号 (X) 相互匹配。 确保连杆盖的朝向正确。 连杆和连杆盖上的锻造标记 (Y) 应在同一侧。 参考图 1。
- 安装新螺栓 (1)。 均匀拧紧螺栓至扭矩为
18 N·m (13 lb ft) 。注: 请勿重复使用旧螺栓来固定连杆盖。
- 均匀拧紧螺栓至扭矩为
40 N·m (30 lb ft) 。 - 使用工具 (B) 再将螺栓转动 120 度。
- 确保连杆组件安装后有能感觉到的侧隙。 小心地转动曲轴,确保没有卡滞。
- 对其余连杆轴承重复步骤 2 至步骤 14。
注: 如果需要更换所有连杆轴承,可以同时在两个气缸上进行本程序。 本程序可在下列气缸配对上同时进行。 1 与 4 和 2 与 3。 确保在从一对气缸换到另一对气缸之前安装完两对连杆轴承。
- 如果卸下了电热塞,安装电热塞。 请参阅拆解和组装, "电热塞 - 安装"。
结束:
- 如果发动机配备平衡器,则安装该平衡器。 请参阅拆解和组装, "平衡器 - 安装"。 如果发动机未配备平衡器,则安装发动机机油泵。 请参阅拆解和组装, "发动机油泵 - 拆卸和安装"。
Caterpillar Information System:
C4.4 Industrial Engine Camshaft Gear - Remove and Install
C4.4 Industrial Engine Camshaft Bearings - Remove and Install
C4.4 Industrial Engine Camshaft - Remove and Install
C4.4 Industrial Engine Boost Pressure Sensor - Remove and Install
C4.4 Industrial Engine Balancer - Remove
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove
C4.4 Industrial Engine Balancer - Install
C4.4 Industrial Engine Alternator Belt - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C4.4 Industrial Engine Coolant Temperature Sensor - Remove and Install
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Filtered Breather
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Unfiltered Breather
C4.4 Industrial Engine Crankshaft - Install
C4.4 Industrial Engine Crankshaft - Remove
C4.4 Industrial Engine Crankshaft Front Seal - Remove and Install
C4.4 Industrial Engine Crankshaft Gear - Remove and Install
C4.4 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C4.4 Industrial Engine Crankshaft Position Sensor - Remove and Install
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Crankshaft Pulley - Remove and Install - Engines With an Automatic Belt Tensioner