Balancer - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 9U-6198 | 曲轴转动工具 | 1 |
B | 230-6283 | 定时销(曲轴) | 1 |
C | 231-8849 | 定时销(平衡器) | 1 |
D | 1P-2320 | 组合式拉拔器 | 1 |
开始:
- 拆下发动机油底壳。 请参阅拆解和组装 , "发动机油底壳 - 拆卸和安装" 。
- 拆下前盖。 请参阅 拆解和组装, "前盖 - 拆卸和安装" 。
注: 要卸下平衡器,必须从机器上卸下发动机。 应将发动机倒置安放在适当的台架上。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 使用工具 (A) 转动曲轴,使 1 号活塞处于上死点位置。
Show/hide table
图 1 g01259627 典型实例 - 将工具 (B) 穿过孔 ( X) 安装到前壳体中。 使用工具 (B),将曲轴锁定到位。
Show/hide table
图 2 g01259635 典型实例 - 卸下螺栓 (3) 和吸入管 ( 2)。
- 从吸入管上卸下垫片。
Show/hide table
图 3 g01252310 典型实例 - 将工具 (C) 安装到平衡器 ( 1) 上。 确保已将工具 ( C) 插入驱动轴 (5) 的孔中。
- 将适当的起吊设备连接在平衡器 ( 1) 上。 支撑平衡器的重量。 平衡器重量约为
23 kg (51 lb) 。 - 拆下螺栓 (4)。 使用起吊设备卸下平衡器。
Show/hide table
图 4 g01259636 - 除非定位销损坏,否则不要卸下定位销 ( 6) 和 (7)。
注: 平衡器装置是一个不可维修的部件。 发动机机油泵和发动机机油安全阀是平衡器中唯一可以维修的部件。
- 卸下发动机机油安全阀。 请参阅拆解和组装 , "发动机机油安全阀 - 拆卸和安装" 。
Show/hide table
图 5 g01478152 典型实例 - 拆下螺栓 (8) 和轮毂 ( 9)。 卸下惰轮 (10) 和止推垫圈 ( 11)。
Show/hide table
图 6 g01259631 典型实例 - 拆下螺母 (12)。 使用工具 (D),从机油泵的轴上卸下齿轮 ( 13)。
注: 不要使用定时销锁定平衡器以此松开螺母 ( 12)。
- 卸下螺栓 (14),然后卸下前盖 ( 15)。
- 卸下外转子 (17),然后卸下内转子 ( 16)。
注: 标出转子的旋向。
Caterpillar Information System:
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove
C4.4 Industrial Engine Balancer - Install
C4.4 Industrial Engine Alternator Belt - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Air Compressor - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Thermistor (Controls Cabinet)
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Storage
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Vacuum Pump Startup - Required Procedure After Extended Storage
3618 Engine Product Lifting
C4.4 Industrial Engine Boost Pressure Sensor - Remove and Install
C4.4 Industrial Engine Camshaft - Remove and Install
C4.4 Industrial Engine Camshaft Bearings - Remove and Install
C4.4 Industrial Engine Camshaft Gear - Remove and Install
C4.4 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C4.4 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C4.4 Industrial Engine Coolant Temperature Sensor - Remove and Install
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Filtered Breather
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Unfiltered Breather
C4.4 Industrial Engine Crankshaft - Install
C4.4 Industrial Engine Crankshaft - Remove
C4.4 Industrial Engine Crankshaft Front Seal - Remove and Install