Turbocharger - Remove
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
注: 塞住并盖好所有端口和管组件。
- 如果涡轮增压器配备一个排气弯头,则卸下该排气弯头。 请参阅拆解和组装 , "排气弯管 - 拆卸和安装 "。
- 松开软管夹,将进气软管从涡轮增压器上断开。
- 松开软管夹,将出气软管从涡轮增压器上断开。 如果发动机配备一个通风管,则卸下该通风管,然后从缸盖上卸下垫片。
- 如果阀机构罩盖配备一个热屏蔽,则卸下该热屏蔽。
Show/hide table
图 1 g01264131 典型实例 - 如果涡轮增压器配备一个适配器 ( 9) ,则卸下螺母 (10) ,然后从涡轮增压器 ( 5) 上卸下适配器 (9)。
- 卸下班卓螺栓 (1),然后从涡轮增压器 ( 5) 上断开管组件 (3)。 从管组件 (3) 上卸下密封垫圈 ( 2)。
如有必要,从执行器 ( 6) 的管组件上卸下管组件 ( 3)。 将管组件 (3) 用夹子固定至执行器的管组件上。
- 从执行器 (6) 上断开软管。
- 卸下班卓螺栓 (4),然后从缸体上卸下管组件 ( 3)。 从管组件 (3) 上卸下密封垫圈 ( 2)。
- 拆下螺栓 (12)。 将管组件 (13) 从涡轮增压器 ( 5) 上断开。 拆下密封垫 ( 11)。
如有必要,卸下螺栓 ( 14),然后从缸体上卸下管组件 ( 13)。 卸下垫片 (15)。
如果用管夹固定管组件 ( 13),则松开管夹紧固件。 如果发动机配有一个顶置涡轮增压器,则必须卸下排气歧管后才能卸下管组件 ( 13)。 请参阅拆解和组装 , "排气歧管 - 拆卸和安装 "。
- 卸下螺母 (8) ,然后卸下涡轮增压器 ( 5)。
注: 不要使用执行器连杆提升涡轮增压器。
- 拆下密封垫 (7)。
- 如有必要,从排气歧管上卸下螺柱。
Caterpillar Information System:
C4.4 Industrial Engine Balancer - Install
C4.4 Industrial Engine Alternator Belt - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Air Compressor - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Thermistor (Controls Cabinet)
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Storage
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Vacuum Pump Startup - Required Procedure After Extended Storage
3618 Engine Product Lifting
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Power Supply PWAs
C4.4 Industrial Engine Balancer - Remove
C4.4 Industrial Engine Boost Pressure Sensor - Remove and Install
C4.4 Industrial Engine Camshaft - Remove and Install
C4.4 Industrial Engine Camshaft Bearings - Remove and Install
C4.4 Industrial Engine Camshaft Gear - Remove and Install
C4.4 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C4.4 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C4.4 Industrial Engine Coolant Temperature Sensor - Remove and Install
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Filtered Breather
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Unfiltered Breather
C4.4 Industrial Engine Crankshaft - Install
C4.4 Industrial Engine Crankshaft - Remove