Balancer - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
E | 4C-4030 | 螺纹锁固胶 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保发动机机油泵的所有部件清洁、无磨损或损坏。
Show/hide table
图 1 g01478152 典型实例 - 安装内转子 (16) 和外转子 ( 17)。 应将旧转子安装在原来的旋向上。 检查外转子与机油泵泵体之间的间隙。 检查内转子与外转子之间的间隙。 检查转子组件的端隙。 更多信息,请参阅 规格, "发动机机油泵 "。
- 使用清洁的发动机机油润滑机油泵组件。 安装前盖 (15)。 安装螺栓 ( 14)。 将螺栓拧紧至扭矩
26 N·m (19 lb ft) 。 - 确保机油泵的轴清洁、干燥。 将齿轮 (13) 放置在轴上。 安装螺母 (12)。 将螺母拧紧至扭矩
95 N·m (70 lb ft) 。注: 不要通过使用定时销锁定平衡器的方式来拧紧螺母 ( 12)。
- 使用清洁的发动机机油润滑轮毂 ( 9)、止推垫圈 (11) 和惰轮 ( 10) 的衬套。 将轮毂 ( 9) 和止推垫圈 (11) 安装到惰轮 ( 10) 上。
注: 确保惰轮的方向正确。
- 将惰轮组件安装到平衡器 ( 1) 上。
- 确保螺栓 (8) 的螺纹清洁、干燥。 将工具 (E) 涂敷在螺栓螺纹上。 安装螺栓 (8)。 将螺栓拧紧至扭矩
26 N·m (19 lb ft) 。 - 检查惰轮 (10) 的端隙。 请参阅规格 , "发动机机油泵" 。
- 安装发动机机油安全阀。 更多信息,请参阅 拆解和组装发动机机油安全阀 - 拆卸与, "安装" 。
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
B | 230-6284 | 定时销(曲轴) | 1 |
C | 231-8849 | 定时销(平衡器) | 1 |
F | 9U-7324 | 千分表支架 | 1 |
7H-1942 | 千分表 | 1 | |
3S-3268 | 千分表触针 | 1 | |
7H-1940 | 通用附件 | 1 | |
G | - | 导螺栓 M10× 75 mm |
2 |
- 确保 1 号活塞处于上死点位置,并且已将工具 ( B) 安装在前盖的 (X) 处。
- 清洁缸体表面。
Show/hide table
图 3 g01252312 - 将工具 (G) 安装到缸体上。
Show/hide table
图 4 g01260306 - 确保定位销 (6) 和 ( 7) 位于平衡器 (1) 壳体中。
Show/hide table
图 5 g01252310 - 将工具 (C) 安装到平衡器 ( 1) 上。 确保已将工具 ( C) 在轴 (5) 中啮合。
- 将适当的起吊设备连接在平衡器上。 平衡器重量约为
23 kg (51 lb) 。 - 使用起吊设备对齐平衡器 ( 1) 与工具 (G)。 将平衡器安装到缸体上。 确保定位销 (6) 和 ( 7) 与缸体中的孔对齐。 确保齿轮 (10) 与曲轴齿轮啮合。 卸下起吊装置。
Show/hide table
图 6 g01259635 - 将螺栓 (4) 安装到平衡器 ( 1) 上,用手拧紧。
- 拆下工具 (G),然后安装其余螺栓 ( 4)。 将螺栓拧紧至扭矩
54 N·m (40 lb ft) 。 - 拆下工具 (B) 和工具 ( C)。
- 将吸入管 (2) 和新垫片安装到平衡器 ( 1) 上。
- 安装螺栓 (3)。 将螺栓拧紧至扭矩
22 N·m (16 lb ft) 。 - 使用工具 (F) 检查齿轮 ( 10) 和 (13) 之间的齿隙。 请参阅插图 4。 请参阅 规格, "发动机机油泵 "。
- 使用工具 (F) 检查齿轮 ( 10) 与曲轴齿轮之间的齿隙。 更多信息,请参阅 规格, "前齿轮总成 "。
Show/hide table
图 2 | g01259627 |
结束:
- 安装发动机油底壳。 请参阅拆解和组装发动机油底壳 - 拆卸和, "安装" 。
- 安装前盖。 请参阅 拆解和组装, "前盖 - 拆卸和安装"。
Caterpillar Information System:
C4.4 Industrial Engine Alternator Belt - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Air Compressor - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Thermistor (Controls Cabinet)
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Storage
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Vacuum Pump Startup - Required Procedure After Extended Storage
3618 Engine Product Lifting
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Power Supply PWAs
2006/06/05 207-5034 Stud Tensioner Tool Gp and 191-5320 Stud Tensioner Tool Gp Require Different Hydraulic Pressures {0701, 0703, 0705, 1100, 1200}
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove
C4.4 Industrial Engine Balancer - Remove
C4.4 Industrial Engine Boost Pressure Sensor - Remove and Install
C4.4 Industrial Engine Camshaft - Remove and Install
C4.4 Industrial Engine Camshaft Bearings - Remove and Install
C4.4 Industrial Engine Camshaft Gear - Remove and Install
C4.4 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C4.4 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C4.4 Industrial Engine Coolant Temperature Sensor - Remove and Install
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Filtered Breather
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Unfiltered Breather
C4.4 Industrial Engine Crankshaft - Install