Boost Pressure Sensor - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 增压压力传感器可能位于辅助燃油滤清器底座上或缸盖中。
- 滑动锁扣 (2) 到解锁位置。
- 从增压压力传感器 (1) 上断开线束组件 (3)。
注: 增压压力传感器具有三线插头。
- 采用深套筒卸下增压压力传感器 (1)。
注: 如有必要,从旁通管上卸下线束组件的支架。
- 从增压压力传感器 (1) 上卸下 O 形密封圈 (4)。
Show/hide table
图 1 | g01480192 |
典型实例 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-6396 | O 形圈组装固定胶 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 增压压力传感器可能位于辅助燃油滤清器底座上或缸盖中。
- 将新的 O 形密封圈 (4) 安装在增压压力传感器 (1) 的槽中。 使用工具 (A) 润滑新 O 形密封圈。
- 采用深套筒安装增压压力传感器 (1)。 拧紧增压压力传感器至扭矩为
10 N·m (89 lb ft) 。注: 如有必要,将线束组件的支架安装在旁通管上。
- 将线束组件 (3) 与增压压力传感器 (1) 连接。
- 滑动锁扣 (2) 到锁定位置。
Show/hide table
图 2 | g01480192 |
典型实例 |
Caterpillar Information System:
C4.4 Industrial Engine Balancer - Remove
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove
C4.4 Industrial Engine Balancer - Install
C4.4 Industrial Engine Alternator Belt - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Air Compressor - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Thermistor (Controls Cabinet)
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Storage
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Vacuum Pump Startup - Required Procedure After Extended Storage
C4.4 Industrial Engine Camshaft - Remove and Install
C4.4 Industrial Engine Camshaft Bearings - Remove and Install
C4.4 Industrial Engine Camshaft Gear - Remove and Install
C4.4 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C4.4 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C4.4 Industrial Engine Coolant Temperature Sensor - Remove and Install
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Filtered Breather
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Unfiltered Breather
C4.4 Industrial Engine Crankshaft - Install
C4.4 Industrial Engine Crankshaft - Remove
C4.4 Industrial Engine Crankshaft Front Seal - Remove and Install
C4.4 Industrial Engine Crankshaft Gear - Remove and Install