Camshaft Bearings - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 8S-2241 | 凸轮轴轴承工具总成 | 1 |
8H-0684 | 棘轮扳手 | 1 |
开始:
- 如果发动机配备平衡器,则卸下该平衡器。 请参阅拆解和组装平衡器 , "- 拆卸" 。 如果发动机未配备平衡器,则卸下发动机机油泵。 请参阅拆解和组装 , "发动机机油泵 - 拆卸"。
- 拆下凸轮轴。 请参阅 拆解和组装, "凸轮轴 - 拆卸和安装 "。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查凸轮轴轴承 ( 1)。 更多信息,请参阅 规格, "凸轮轴轴承 "。
- 如果凸轮轴轴承 ( 1) 磨损或损坏,使用工具 ( A) 从缸体上卸下凸轮轴轴承。
注: 从缸体前部卸下凸轮轴轴承。
Show/hide table
图 1 | g01270437 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 8S-2241 | 凸轮轴轴承工具总成 | 1 |
8H-0684 | 棘轮扳手 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁缸体中的轴承壳。 确保轴承壳的油孔中无碎屑。
Show/hide table
图 2 g01266512 - 使用清洁的发动机机油润滑缸体中的轴承壳。
- 将凸轮轴轴承 (1) 中的两个油孔 ( X) 与缸体中的两个油孔准确对齐。
注: 凸轮轴轴承中的槽 ( Y) 必须处于缸体顶部。
- 使用工具 (A),将凸轮轴轴承 ( 1) 安装进缸体中。 安装凸轮轴轴承,使轴承前端与缸体中的凹槽面齐平。
注: 确保已将所有油孔正确对齐。 如果没有正确对齐油孔,应卸下凸轮轴轴承。
结束:
- 安装凸轮轴。 请参阅 拆解和组装, "凸轮轴 - 拆卸和安装 "。
- 如果发动机配备平衡器,则安装该平衡器。 请参阅拆解和组装平衡器 , "- 安装" 。 如果发动机未配备平衡器,则安装发动机机油泵。 请参阅拆解和组装 , "发动机机油泵 - 安装"。
Caterpillar Information System:
C4.4 Industrial Engine Camshaft - Remove and Install
C4.4 Industrial Engine Boost Pressure Sensor - Remove and Install
C4.4 Industrial Engine Balancer - Remove
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove
C4.4 Industrial Engine Balancer - Install
C4.4 Industrial Engine Alternator Belt - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Air Compressor - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Thermistor (Controls Cabinet)
C4.4 Industrial Engine Camshaft Gear - Remove and Install
C4.4 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C4.4 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C4.4 Industrial Engine Coolant Temperature Sensor - Remove and Install
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Filtered Breather
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Unfiltered Breather
C4.4 Industrial Engine Crankshaft - Install
C4.4 Industrial Engine Crankshaft - Remove
C4.4 Industrial Engine Crankshaft Front Seal - Remove and Install
C4.4 Industrial Engine Crankshaft Gear - Remove and Install
C4.4 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C4.4 Industrial Engine Crankshaft Position Sensor - Remove and Install