Camshaft - Remove and Install
开始:
- 拆下摇臂轴和推杆。 请参阅拆解和组装, "摇臂轴和推杆 - 拆卸"。
- 拆下前壳体。 请参阅拆解和组装, "壳体(前) - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 应将发动机倒置安装在适当的支架上。
Show/hide table
图 1 g01266056 典型实例 - 从缸体上卸下止推垫圈 (1)。 除非定位销损坏,否则不要从缸体上卸下定位销 (2)。
注: 止推垫圈可能有一个或两个槽 (X)。
Show/hide table图 2 g01266057 Show/hide table注意 拆卸或安装凸轮轴时不要损坏凸轮或轴承。
- 小心地从缸体上卸下凸轮轴 (3)。
- 除非钥匙损坏,否则不要从凸轮轴 (3) 上卸下钥匙 (4)。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁凸轮轴和止推垫圈。 检查凸轮轴和止推垫圈是否磨损和损坏。 更多资料,请参阅技术规格, "凸轮轴"。 更换任何损坏或磨损的部件。
- 清洁缸体中的凸轮轴轴承。 检查凸轮轴轴承是否磨损和损坏。 更多信息,请参阅规格凸轮轴, "轴承"。 如有必要,更换凸轮轴轴承。 请参阅拆解和组装, "凸轮轴轴承 - 拆卸和按装"。
Show/hide table
注意 强烈推荐应在安装新凸轮轴时更换所有的挺杆。
- 检查挺杆是否磨损和损坏。 更多信息,请参阅规格挺杆, "总成"。 更换所有磨损或损坏的挺杆。 请参阅拆解和组装, "挺杆总成 - 拆卸和安装"。
Show/hide table
图 3 g01266057 - 如有必要,将新钥匙 (4) 安装到凸轮轴 (3) 上。
- 使用清洁的发动机机油润滑凸轮轴 (3) 的轴承面和凸轮轴的凸轮。
Show/hide table
注意 拆卸或安装凸轮轴时不要损坏凸轮或轴承。
- 小心地将凸轮轴 (3) 安装到缸体中。
Show/hide table
图 4 g01266056 典型实例 - 使用清洁的发动机机油润滑止推垫圈。 将止推垫圈 (1) 中的槽 (X) 与缸体中的定位销 (2) 对齐。 将止推垫圈 (1) 安装到缸体的凹槽中。
注: 止推垫圈可能有一个或两个槽。
结束:
- 安装前壳体。 请参阅拆解和组装, "壳体(前) - 安装"。
- 安装摇臂轴和推杆。 请参阅拆解和组装, "摇臂轴和推杆 - 安装"。
Caterpillar Information System:
C4.4 Industrial Engine Boost Pressure Sensor - Remove and Install
C4.4 Industrial Engine Balancer - Remove
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove
C4.4 Industrial Engine Balancer - Install
C4.4 Industrial Engine Alternator Belt - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Alternator - Install - Engines With an Automatic Belt Tensioner
C4.4 Industrial Engine Air Compressor - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Thermistor (Controls Cabinet)
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Storage
C4.4 Industrial Engine Camshaft Bearings - Remove and Install
C4.4 Industrial Engine Camshaft Gear - Remove and Install
C4.4 Industrial Engine Connecting Rod Bearings - Install - Connecting rods in position
C4.4 Industrial Engine Connecting Rod Bearings - Remove - Connecting rods in position
C4.4 Industrial Engine Coolant Temperature Sensor - Remove and Install
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Filtered Breather
C4.4 Industrial Engine Crankcase Breather - Remove and Install - Unfiltered Breather
C4.4 Industrial Engine Crankshaft - Install
C4.4 Industrial Engine Crankshaft - Remove
C4.4 Industrial Engine Crankshaft Front Seal - Remove and Install
C4.4 Industrial Engine Crankshaft Gear - Remove and Install
C4.4 Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in Position