Water Temperature Regulator - Remove and Install
Show/hide table
热的冷却液、蒸汽和碱会造成人身伤害。 在工作温度下,发动机冷却液是热的而且处在压力下。 散热器和所有到加热器的管路或发动机中都有热的冷却液或蒸汽。 与它们的任何接触都会造成严重烫伤。 只有当发动机停机且冷却系统压力盖已经冷却到可以徒手触摸时,再慢慢拆下冷却系统压力盖以释放压力。 不要试图在冷却液还热的时候去拧紧软管接头,软管会脱落而造成灼伤。 警告:冷却系统的冷却液添加剂含碱。 应避免它与皮肤和眼睛接触。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 从冷却系统将冷却液排入合适的容器以便保存或废弃这些冷却液。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
Show/hide table
图 1 g01173069 - 从水温调节器壳体 (2) 上卸下螺栓 (1)。
Show/hide table
图 2 g01173071 - 卸下水温调节器壳体 (2)。 拆卸密封垫 (3)。 拆卸水温调节器 (4)。
Show/hide table
图 3 g01173074 - 从水温调节器壳体 (2) 上卸下密封件 (5)。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 221-8647 | 油封安装工具 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁水温调节器壳体的配合面。
Show/hide table
图 4 g01173077 - 使用工具 (A) 将密封件 (5) 安装到水温调节器壳体 (2) 中。
Show/hide table
图 5 g01173071 Show/hide table图 6 g01173069 - 安装水温调节器 (4)。 安装一个新的密封垫 (3)。
- 安置水温调节器壳体 (2)。 安装螺栓 (1)。
- 向冷却系统加注冷却液。 请参考操作和保养手册, "冷却系统冷却液(ELC)- 更换"和操作和保养手册, "容量(加注)"。
Caterpillar Information System:
C11 and C13 Engines Valve Rocker Arm
3406E Marine Engine Engine Support (Front) - Remove and Install
PL1000E Communication ECM General Information
3500 Generator Sets Electrical System
C9 Engine for Caterpillar Built Machines Engine Oil Pump - Assemble
G3500 Engines Air Starting Motor - Assemble
C13 and C15 On-highway Engines Coolant Level - Test
C7 and C9 On-Highway Engines Air Inlet Heater - Test
C9 Engine for Caterpillar Built Machines Engine Oil Pump - Disassemble
C7 On-highway Engine Fuel Filter Base
C9 Engine for Caterpillar Built Machines Engine Oil Pump - Install
3500 Industrial and Generator Set Engines Sea Water Strainer - Clean/Inspect - if equipped
C13 and C15 On-highway Engines Injector Trim File - Install
C4.4 Industrial Engine Engine Valve Lash - Inspect/Adjust
C4.4 Industrial Engine Fuel Tank Water and Sediment - Drain
C4.4 (Mech) Industrial Engine Starting Motor - Inspect
C9 Engine for Caterpillar Built Machines Flywheel - Remove and Install
C7 On-highway Engine Fuel System - Prime
C7 On-highway Engine Fuel System Pressure - Test
PL1000E Communication ECM Features
C9 Engine for Caterpillar Built Machines Crankshaft Front Seal - Remove
C27 and C32 Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
PL1000E Communication ECM Electronic Control Module (ECM)
C27 and C32 Engines for Caterpillar Built Machines Engine Speed/Timing Sensor - Calibrate