Flywheel - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺栓 M16 x 2 x 8 in |
1 |
Show/hide table
图 1 | g01173265 |
Show/hide table
图 2 | g01173268 |
- 拆下一条螺栓 (1)。 安装工具 (A)。 拆下剩余的螺栓 (1)。
- 将适当的起吊设备连接到飞轮 (2) 上。 飞轮 (2) 的重量约为
31 kg (68 lb) 。 拆下飞轮 (2)。 - 检查齿圈。 如有必要,更换齿圈。 将飞轮放到木块上。 使用锤子和冲头来拆卸齿圈。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺栓 M16 x 2 x 8 in |
1 |
B | 9S-3263 | 螺纹锁固胶 | 1 |
- 加热新齿圈。 将齿圈安装在飞轮上。 放置齿圈,让零件号朝向曲轴。 让齿圈冷却。 使用软面锤来使齿圈坐落到飞轮的凸肩。
Show/hide table
图 3 g01173268 - 将工具 (A) 安装在曲轴中。 将适当的起吊设备连接到飞轮 (2) 上。 飞轮 (2) 的重量约为
31 kg (68 lb) 。注: 安装时应使用新的螺栓。
Show/hide table图 4 g01173265 - 将飞轮 (2) 放置到发动机上。 对准飞轮和曲轴上的箭头。 将工具 (B) 涂敷到螺栓 (1) 的螺纹上,然后安装螺栓。 均匀拧紧螺栓至扭矩为
300 ± 40 N·m (221 ± 30 lb ft) 。 - 检查飞轮跳动。 请参阅测试与调整, "飞轮 - 检查"。
Caterpillar Information System:
C4.4 (Mech) Industrial Engine Starting Motor - Inspect
C4.4 Industrial Engine Fuel Tank Water and Sediment - Drain
C4.4 Industrial Engine Engine Valve Lash - Inspect/Adjust
C13 and C15 On-highway Engines Injector Trim File - Install
C9 Engine for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C11 and C13 Engines Valve Rocker Arm
3406E Marine Engine Engine Support (Front) - Remove and Install
PL1000E Communication ECM General Information
3500 Generator Sets Electrical System
C9 Engine for Caterpillar Built Machines Engine Oil Pump - Assemble
G3500 Engines Air Starting Motor - Assemble
C13 and C15 On-highway Engines Coolant Level - Test
C7 On-highway Engine Fuel System - Prime
C7 On-highway Engine Fuel System Pressure - Test
PL1000E Communication ECM Features
C9 Engine for Caterpillar Built Machines Crankshaft Front Seal - Remove
C27 and C32 Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
PL1000E Communication ECM Electronic Control Module (ECM)
C27 and C32 Engines for Caterpillar Built Machines Engine Speed/Timing Sensor - Calibrate
C9 Engine for Caterpillar Built Machines Crankshaft Front Seal - Install
PL1000E Communication ECM General Information
C7 PETROLEUM Petroleum Engine Front Cover - Remove and Install
PL1000E Communication ECM Service Tools
PL1000E Communication ECM Connector Locations