Engine Oil Pump - Assemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-0510 | 冲头总成 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 组装前,确保机油泵的所有零件完全洁净。
注: 利用洁净的机油润滑机油泵的所有内构件。
Show/hide table图 1 g01271413 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 将机油油压释放柱塞 (12) 和弹簧 (13) 安装到机油泵壳组件 (7) 内。 安装机油塞 (14)。
Show/hide table
图 2 g01172656 - 将轴组件 (11) 安装到机油泵壳组件 (7) 内。
- 将轴组件 (8) 安装到机油泵壳 (9) 内。
- 将机油泵壳 (9) 放置到机油泵壳组件 (7) 上,然后安装螺栓 (10)。
Show/hide table
图 3 g01271430 - 将驱动齿轮 (6) 压到轴组件 (8) 上,直到驱动齿轮 (6) 与轴组件 (8) 的端部齐平。
- 将机油泵轴 (5) 安装到机油泵壳组件 (7) 上。 使用工具 (A),将轴承安装到惰轮 (4) 中。 安装轴承,使惰轮 (4) 的轮毂螺栓面和轴承间的距离为
0.75 ± 0.25 mm (0.030 ± 0.010 in) 。 - 将惰轮 (4) 安装到机油泵的轴 (5) 上。 安装垫圈和螺栓 (3)。 将螺栓 (3) 上紧到
70 ± 15 N·m (52 ± 11 lb ft) 。Show/hide table图 4 g01271408 - 检查用于吸油管 (1) 的管组件的密封垫的状况。 如果密封垫损坏,则更换密封垫。 安装吸油管 (1) 的密封垫和管组件。
- 检查用于出口弯头 (2) 中的 O 形密封圈的状况。 如果 O 形密封圈损坏,更换 O 形密封圈。 安装 O 形密封圈和出口弯头 (2)。
结束:
- 安装发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
G3500 Engines Air Starting Motor - Assemble
C13 and C15 On-highway Engines Coolant Level - Test
C7 and C9 On-Highway Engines Air Inlet Heater - Test
C9 Engine for Caterpillar Built Machines Engine Oil Pump - Disassemble
C7 On-highway Engine Fuel Filter Base
C9 Engine for Caterpillar Built Machines Engine Oil Pump - Install
3500 Industrial and Generator Set Engines Sea Water Strainer - Clean/Inspect - if equipped
C9.3 Engines for Caterpillar Built Machines Lubrication System
3500 Industrial and Generator Set Engines Auxiliary Water Pump - Inspect - if equipped
3500 and 3500B Engines Heat Exchanger - Inspect - if equipped
C13 and C15 On-highway Engines Air Shutoff - Test
C9 Engine for Caterpillar Built Machines Engine Oil Pump - Remove
3500 Generator Sets Electrical System
PL1000E Communication ECM General Information
3406E Marine Engine Engine Support (Front) - Remove and Install
C11 and C13 Engines Valve Rocker Arm
C9 Engine for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C13 and C15 On-highway Engines Injector Trim File - Install
C4.4 Industrial Engine Engine Valve Lash - Inspect/Adjust
C4.4 Industrial Engine Fuel Tank Water and Sediment - Drain
C4.4 (Mech) Industrial Engine Starting Motor - Inspect
C9 Engine for Caterpillar Built Machines Flywheel - Remove and Install
C7 On-highway Engine Fuel System - Prime
C7 On-highway Engine Fuel System Pressure - Test