Engine Oil Pump - Disassemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-0510 | 冲头总成 | 1 |
B | 1P-2320 | 组合式拉拔器 | 1 |
开始:
- 拆卸发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 从吸油管 (1) 上拆下管组件,从机油泵上拆下密封垫。 从机油泵上拆下螺栓和出口弯头 (2)。
Show/hide table
图 2 g01271410 - 将螺栓 (3)、垫圈和惰轮 (4) 从机油泵上拆下。
- 使用工具 (A) 和适当的压具将轴承从惰轮 (4) 上拆下。
- 将机油泵轴 (5) 从机油泵壳组件 (7) 上拆下。
- 使用工具 (B) 拆下驱动齿轮 (6)。
Show/hide table
图 3 g01172656 - 拆下螺栓 (10)。 将机油泵壳 (9) 从机油泵壳体组件 (7) 上分离。
Show/hide table
注意 从泵壳上拆下驱动轴之前,确保驱动轴上没有毛刺。 如果驱动轴上有毛刺,很可能会划伤泵壳内孔。
- 将轴组件 (8) 和轴组件 (11) 从机油泵壳 (9) 上拆下。
Show/hide table
图 4 g01271413 Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
- 从机油泵壳组件 (7) 上拆下以下零件:机油塞 (14), 弹簧 (13) 和 机油压力释放柱塞 (12)。
Show/hide table
图 1 | g01271408 |
Caterpillar Information System:
C7 On-highway Engine Fuel Filter Base
C9 Engine for Caterpillar Built Machines Engine Oil Pump - Install
3500 Industrial and Generator Set Engines Sea Water Strainer - Clean/Inspect - if equipped
C9.3 Engines for Caterpillar Built Machines Lubrication System
3500 Industrial and Generator Set Engines Auxiliary Water Pump - Inspect - if equipped
3500 and 3500B Engines Heat Exchanger - Inspect - if equipped
C13 and C15 On-highway Engines Air Shutoff - Test
C9 Engine for Caterpillar Built Machines Engine Oil Pump - Remove
C18 Marine Generator Set Engines Sensors and Electrical Connectors
C9 Marine Auxiliary and Marine Generator Set Engines Coolant Temperature Is Too High
C27 and C32 Industrial and Petroleum Engines System Configuration Parameters
C13 and C15 On-highway Engines Sensor Signal (PWM) - Test
C7 and C9 On-Highway Engines Air Inlet Heater - Test
C13 and C15 On-highway Engines Coolant Level - Test
G3500 Engines Air Starting Motor - Assemble
C9 Engine for Caterpillar Built Machines Engine Oil Pump - Assemble
3500 Generator Sets Electrical System
PL1000E Communication ECM General Information
3406E Marine Engine Engine Support (Front) - Remove and Install
C11 and C13 Engines Valve Rocker Arm
C9 Engine for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C13 and C15 On-highway Engines Injector Trim File - Install
C4.4 Industrial Engine Engine Valve Lash - Inspect/Adjust
C4.4 Industrial Engine Fuel Tank Water and Sediment - Drain