Track - Connect
Procedure to Connect the Track
Start By:
- Assemble the Track. See the procedure in Undercarriage Reconditioning Guide, SEBF8599.
- Place the track under the machine. Lower the side of the machine on track (8) .
Show/hide table
Illustration 1 | g00629456 |
- Fasten one end of a chain to track (8) and fasten the other end to another machine.
- Lift the end of the track. Place wood blocks under the grouser. See Illustration 1.
Note: In order to avoid damage to the track or to the machine, pull the track in a straight line.
- Pull the track until the track bushings engage with the sprocket on the final drive.
- Start the machine. Turn the final drive in the reverse direction in order to pull the track together.
Note: Make sure that the serrations on the master links are clean and dry.
- Align the lower ends with the upper ends of master links (7) . Make sure that the serrations of both ends are engaged.
Show/hide table
Illustration 2 | g00629455 |
- Move the track until the master link is aligned with the centerline of rear idler (6) . Place master shoe (5) in position on the master links. Apply 4C-5593 Anti-Seize Compound to the following components: the threads, the shank and the faces of the washers for master link bolts (4) . Tighten bolts (4) to a torque of 340 ± 70 N·m (250 ± 50 lb ft). Then, tighten the bolts by an additional turn of 120 degrees.
Show/hide table
Illustration 3 | g00629453 |
- Tighten relief valve (2) and tighten track adjustment valve (3) to a torque of 35 ± 7 N·m (26 ± 5 lb ft).
ReferenceWhen you adjust the tension of the track, refer to the procedure in Testing and Adjusting, "Track - Adjust" in the Service Manual in this module.
Show/hide table
Illustration 4 | g00629451 |
- Install the track adjuster cover (1) on the track roller frame.
Show/hide table
Illustration 5 | g00629450 |
Caterpillar Information System:
D7R Track-Type TractorPower Train Track - Assemble
D7R Track-Type TractorPower Train Track - Disassemble
D7R Track-Type TractorPower Train Track - Separate
D7R Track-Type TractorPower Train Track Roller - Install
D7R Track-Type TractorPower Train Track Roller - Assemble
973 Track-Type Loader Steering Linkage - Lubricate
D7R Track-Type TractorPower Train Track Roller - Disassemble
963B Track-Type Loader Burn Prevention
D7R Track-Type TractorPower Train Track Roller - Remove
D7R Track-Type TractorPower Train Bottom Guard - Remove and Install
D9R Track-Type Tractor Equalizer Bar End Pins - Lubricate
D8R Track-Type Tractor Hydraulic System Filter (Steering)
D7R Track-Type TractorPower Train Sprocket Segment - Remove and Install
611 Wheel Tractor-Scraper Cooling System Coolant (DEAC) - Change
D7R Track-Type TractorPower Train Track Roller Frame - Remove
D7R Track-Type TractorPower Train Pivot Shaft Seals-Disassemble
D7R Track-Type TractorPower Train Pivot Shaft Seals-Assemble
D7R Track-Type TractorPower Train Track Roller Frame - Install
D7R Track-Type TractorPower Train Front Track Roller Frame - Remove
D7R Track-Type TractorPower Train Front Track Roller Frame - Install
D8R Track-Type Tractor Hydraulic System Bulldozer and Ripper Control Linkage
D7R Track-Type TractorPower Train Track Adjuster - Remove
D7R Track-Type TractorPower Train Track Adjuster - Disassemble
D7R Track-Type TractorPower Train Track Adjuster - Assemble