Pivot Shaft Seals-Disassemble
Disassembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Description     | Qty     |
A     | 0S-1587     | Bolt (1/2 inch by 13 by 1 3/4 inch)     | 1     |
1F-7958 | Nut (1/2 inch by 13)     | 1     | |
B     |     | Bar Stock (1/2 inch by 2 inch by 10 inch)     | 4     |
C     | FT-1395     | Plate     | 1     |
1H-3110 | Bearing Puller     | 1     |
Start By:
- Remove the track roller frame. See the procedure in Disassembly and Assembly, "Track Roller Frame - Remove" in this module.
Show/hide table
Personal injury can result from performing service on the track roller frame. Refer to Special Instruction, SMHS8273 for inspection and removal procedures before performing any service. |
- Place the track roller frame on a level surface. Support each end of the track roller frame with the track guides.
- Remove O-ring seal (3) from seal retainer (4) .
Show/hide table
Illustration 1 | g00837626 |
- Remove eight bolts (1) from retainer (2). Remove both retainers from the track roller frame.
- Remove the O-ring seal from retainer (2) which seals between the retainer and the track roller frame.
- Position Tooling (A) according to Illustration 2. Turn the bolt outward in order to apply pressure to plate (5). When plate (5) and retainer (4) are separated sufficiently, install Tooling (B) in order to maintain separation. Repeat this step at three other points around the retainer.
Show/hide table
Illustration 2 | g00626423 |
Show/hide table
Illustration 3 | g00837631 |
- Use a soft hammer around the outer diameter of the retainer in order to loosen plate (5). Remove plate (5) .
- Place both retainers in a press. Use Tooling (C) in order to remove retainer (2) from retainer (4) .
Show/hide table
Illustration 4 | g00837638 |
- Use a press or a hammer in order to remove seal (6) from retainer (4). If necessary, use a punch.
Show/hide table
Illustration 5 | g00837644 |
- If two bearings (7) are damaged, remove the bearings from the sides of the track roller frame.
Note: If two bearings (7) are removed from the track roller frame, the bearings are destroyed.
Show/hide table
Illustration 6 | g00837645 |
- Mark the track rollers and the track roller frame, so that the single flange rollers are installed in the original locations, and the double flange rollers are installed in the original locations. Remove the track rollers. See the procedure in Disassembly and Assembly, "Track Roller - Remove" in this module.
- Remove the track idlers. See the procedure in Disassembly and Assembly, "Idler - Remove" in this module.
Caterpillar Information System:
D7R Track-Type TractorPower Train Track Roller Frame - Remove
611 Wheel Tractor-Scraper Cooling System Coolant (DEAC) - Change
D7R Track-Type TractorPower Train Sprocket Segment - Remove and Install
D7R Track-Type TractorPower Train Track - Connect
D7R Track-Type TractorPower Train Track - Assemble
D7R Track-Type TractorPower Train Track - Disassemble
D7R Track-Type TractorPower Train Track - Separate
D7R Track-Type TractorPower Train Track Roller - Install
D7R Track-Type TractorPower Train Track Roller - Assemble
973 Track-Type Loader Steering Linkage - Lubricate
D7R Track-Type TractorPower Train Track Roller - Disassemble
963B Track-Type Loader Burn Prevention
D7R Track-Type TractorPower Train Pivot Shaft Seals-Assemble
D7R Track-Type TractorPower Train Track Roller Frame - Install
D7R Track-Type TractorPower Train Front Track Roller Frame - Remove
D7R Track-Type TractorPower Train Front Track Roller Frame - Install
D8R Track-Type Tractor Hydraulic System Bulldozer and Ripper Control Linkage
D7R Track-Type TractorPower Train Track Adjuster - Remove
D7R Track-Type TractorPower Train Track Adjuster - Disassemble
D7R Track-Type TractorPower Train Track Adjuster - Assemble
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Piston Motor (Hydrostatic)
D7R Track-Type TractorPower Train Track Adjuster - Install
D6R Track-Type Tractor 3306B Engine Supplement Alternator - Remove and Install
D7R Track-Type TractorPower Train Idler - Remove