Flywheel - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 138-7573     | 连杆支架     | 2     |
B     | FT2712     | 导向螺柱     | 2     |
C     | 7M-7456     | 轴承安装固定胶     | 1     |
- 升高齿圈的温度到最大温度 315 °C (599 °F)。 放置齿圈,让零件号朝向曲轴。 将齿圈安装到飞轮上。 让齿圈冷却下来。 使用软面锤来使齿圈坐落到飞轮的凸肩。
Show/hide table
操作已经加热的零件时要坚持戴防护手套。 |
- 将工具 (A) 安装到飞轮 (2) 上。 将适当提升设备固定到飞轮 (2) 上。 飞轮的重量约为 41 kg (90 lb)。
Show/hide table
图 1 | g01010803 |
- 把飞轮 (2) 放在曲轴上。 在工具 (B) 上滑动飞轮。
- 在螺栓 (1) 螺纹上使用工具 (C) 。
- 安装 8 个螺栓 (1) 其中的 6 个。 从曲轴端口拆卸工具 (B) 并用两个剩余的螺栓代替。 均匀地将螺栓拧紧至扭矩 300 ± 40 N•m (221 ± 30 lb ft)。
- 检查飞轮偏差。 有关正确程序,请参考测试与调整, "飞轮 - 检查"。
Caterpillar Information System:
C13 Engine Flywheel - Remove
C11 and C13 Engines Water Temperature Regulator - Remove and Install
C11 and C13 Engines Diverter Valve (Oil) - Install
C11 and C13 Engines Diverter Valve (Oil) - Remove
C13 Engine Engine Control Module - Remove and Install
C11 and C13 Engines Air Compressor - Remove and Install
C13 Engine Exhaust Manifold - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Pump - Assemble
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Pump - Disassemble
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Filter Base - Assemble
C11 and C13 Engines Flywheel Housing - Remove and Install
2003/09/01 The Oil Pan Gasket now Requires a Gasket Sealant to be Used {1302, 7555}
C32 Auxiliary Engine Battery Charger - Check
C13 Engine Turbocharger - Remove - Low Pressure Turbocharger
C13 Engine Turbocharger - Install - Low Pressure Turbocharger
3406C Marine Auxiliary Generator Set Reference Material
C11 and C13 Engines Engine Sensors - Remove and Install
C11 and C13 Engines Camshaft - Remove
Cat® Digital Voltage Regulator General Information
C15 and C18 Petroleum Generator Sets Standby Generator Set Maintenance Recommendations
C13 Engine Housing (Front) - Remove
C13 Engine Housing (Front) - Install