Camshaft - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
A     | 201-4211     | 凸轮轴导向器     | 1     |
201-4212 | 凸轮轴导向器     | 1     |
开始:
- 拆卸摇臂轴组件和推杆。 请参考解体及组装, "摇臂轴和推杆 - 拆卸"。
- 拆卸前盖。 请参考解体及组装, "前盖 - 拆卸"。
- 拆卸凸轮轴位置传感器。 请参考解体及组装, "发动机传感器 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 旋转曲轴到 1 号活塞压缩行程的上止点。 在飞轮中安装正时螺栓。 这用于安装正时。
- 确保下列齿轮的正时标识是对准的: 凸轮轴驱动齿轮, 惰轮 和 曲轴齿轮。
- 让气门挺杆的电线脱离凸轮轴。 见图 1。
Show/hide table
图 1 | g01011038 |
注: 为了拆下凸轮轴,没有必要拆卸缸盖。
- 拆卸螺栓 (1) 。
Show/hide table
图 2 | g01011039 |
- 将工具 (A) 安装到凸轮轴中。
Show/hide table
图 3 | g01011040 |
- 从发动机小心拆卸凸轮轴 (2) 。
Show/hide table
图 4 | g01011042 |
注: 润滑工具 (A) 以便更易于拆下凸轮轴。 润滑还防止损坏凸轮轴凸轮和凸轮轴轴承。
Caterpillar Information System:
C11 and C13 Engines Engine Sensors - Remove and Install
3406C Marine Auxiliary Generator Set Reference Material
C13 Engine Turbocharger - Install - Low Pressure Turbocharger
C13 Engine Turbocharger - Remove - Low Pressure Turbocharger
C32 Auxiliary Engine Battery Charger - Check
2003/09/01 The Oil Pan Gasket now Requires a Gasket Sealant to be Used {1302, 7555}
C11 and C13 Engines Flywheel Housing - Remove and Install
C13 Engine Flywheel - Install
C13 Engine Flywheel - Remove
C11 and C13 Engines Water Temperature Regulator - Remove and Install
C11 and C13 Engines Diverter Valve (Oil) - Install
C11 and C13 Engines Diverter Valve (Oil) - Remove
Cat® Digital Voltage Regulator General Information
C15 and C18 Petroleum Generator Sets Standby Generator Set Maintenance Recommendations
C13 Engine Housing (Front) - Remove
C13 Engine Housing (Front) - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Accessory Drive - Remove
C11 and C13 Engines for Caterpillar Built Machines Accessory Drive - Install
3406C Marine Auxiliary Generator Set Engine Air Cleaner Element - Clean/Replace
C11 and C13 Engines Camshaft - Install
C9 On-highway Engines Engine Oil Level Gauge - Calibrate
2003/07/01 Replacement of the Piston Cooling Jet {1331}