Turbocharger - Install - Low Pressure Turbocharger
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 5P-3931     | 防粘结剂     | 1     |
Show/hide table
注意 |
---|
不遵守下列规定程序可能导致零件损坏。 为了避免损坏零件,总是确认和标记零件,以便零件可以安装在相同的位置。 |
Show/hide table
注意 |
---|
波纹管的定位很重要。 不正确的定位会导致波纹管过早损坏。 目视检查波纹压缩是否一致,来判断是否定位好。 安装之前,检查波纹管是否有损伤。 如果波纹有任何损坏,废弃此波纹管。 波纹管口的微小破损可以修复。 然而,如果修理后安装有任何困难,废弃此波纹管。 |
注: 有关更多处理波纹管的信息,请参阅专门说明书, REHS1728, "波纹管应用指南"。
- 使用适当的提升装置。 涡轮增压器的重量约为 29 kg (65 lb)。 在发动机上安装涡轮增压器 (13) 。
Show/hide table
图 1 | g01010976 |
Show/hide table
图 2 | g01383085 |
- 将工具 (A) 涂敷在三个螺柱 (15) 上。 将三个螺柱 (15) 安装在排气歧管上,并将螺柱拧紧至扭矩 35 ± 5 N·m (26 ±4 lb ft)。 螺柱 (Z) 安装在涡轮增压器上。 将工具 (A) 涂敷在螺柱 (Z) 上。 将螺柱 (Z) 安装在涡轮增压器上,并将螺柱 (Z) 拧紧至扭矩 35 ± 5 N·m (26 ±4 lb ft)。 安装螺母 (12) 并拧紧螺母 (12) 至扭矩为 70 ± 5 N·m (58 ± 4 lb ft)。
注: 安装螺柱,使字母"X"可见。
- 连接供油管组件 (2) 和排油管组件 (10) 。
- 安装卡箍 (9) 。
- 连接弯头 (1) 。
- 安装弯头 (3) 。
- 安装弯头 (8) 和弯头 (14) 。
- 将工具 (A) 涂敷在卡箍 (6) 的螺柱螺纹上。
- 将卡箍 (6) 放置在波纹管 (7) 上。
- 将卡箍 (6) 拧紧至扭矩 12 N·m (106 lb in)。
- 安装卡箍 (11) 。
- 将工具 (A) 涂敷在卡箍 (4) 的螺柱螺纹上。
- 将卡箍 (4) 放置在波纹管 (5) 上。
- 将卡箍 (4) 拧紧至扭矩 12 N·m (106 lb in)。
Caterpillar Information System:
C13 Engine Turbocharger - Remove - Low Pressure Turbocharger
C32 Auxiliary Engine Battery Charger - Check
2003/09/01 The Oil Pan Gasket now Requires a Gasket Sealant to be Used {1302, 7555}
C11 and C13 Engines Flywheel Housing - Remove and Install
C13 Engine Flywheel - Install
C13 Engine Flywheel - Remove
C11 and C13 Engines Water Temperature Regulator - Remove and Install
C11 and C13 Engines Diverter Valve (Oil) - Install
C11 and C13 Engines Diverter Valve (Oil) - Remove
C13 Engine Engine Control Module - Remove and Install
C11 and C13 Engines Air Compressor - Remove and Install
C13 Engine Exhaust Manifold - Remove and Install
3406C Marine Auxiliary Generator Set Reference Material
C11 and C13 Engines Engine Sensors - Remove and Install
C11 and C13 Engines Camshaft - Remove
Cat® Digital Voltage Regulator General Information
C15 and C18 Petroleum Generator Sets Standby Generator Set Maintenance Recommendations
C13 Engine Housing (Front) - Remove
C13 Engine Housing (Front) - Install
C11 and C13 Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Accessory Drive - Remove
C11 and C13 Engines for Caterpillar Built Machines Accessory Drive - Install
3406C Marine Auxiliary Generator Set Engine Air Cleaner Element - Clean/Replace