Track Carrier Roller - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
(A)     | 8T-5255     | Hydraulic Jack     | 2     |
Show/hide table
Personal injury or death can result from grease and oil coming out of the relief valve. Grease and oil are under high pressure coming out of the relief valve and can penetrate the body. Do not watch the relief valve to see if grease is escaping. Watch the track or track adjustment cylinder to see if the track is being loosened. Make sure the vent holes are clean before the tension is released on the track. |
- Put the machine on a flat level surface.
- Release the tension on the track. Loosen relief valve (1) for one turn only. If the track does not loosen after opening the relief valve, move the machine forward and backward until the tension is released.
Show/hide table
Illustration 1 | g00481091 |
- Loosen bolt (2) that holds track carrier roller (3) to the mounting bracket to the undercarriage frame.
Show/hide table
Illustration 2 | g00481092 |
- Put wood blocks and Tooling (A) under the track assembly, as shown. Lift the track assembly off the track carrier roller. Remove track carrier roller (3). The weight of the track carrier roller is 23 kg (50 lb).
Show/hide table
Illustration 3 | g00481093 |
Caterpillar Information System:
3126B and 3126E On-highway Engines 0128-04 Secondary Fuel Level voltage low
3126B and 3126E On-highway Engines 0128-03 Secondary Fuel Level voltage high
Power Module Switchgear (Low Voltage and Medium Voltage) Initial Startup Safety Check
Power Module Switchgear (Low Voltage and Medium Voltage) Installation
3126B and 3126E On-highway Engines 0096-04 Fuel Level voltage low
Power Module Switchgear (Low Voltage and Medium Voltage) Handling
Power Module Switchgear (Low Voltage and Medium Voltage) Storage
Power Module Switchgear (Low Voltage and Medium Voltage) Receiving Inspection
G3408 and G3412 Engines Engine Speed/Timing Sensor - Clean/Inspect
3054 and 3056 Engines 520 Generator Set Control Panel Factory Default Values of Configuration Parameters
3126B and 3126E On-highway Engines 0096-03 Fuel Level voltage high
3054 and 3056 Engines 520 Generator Set Control Panel Wiring Diagrams
2001/11/01 Changes were made in the Communication Link for the Marine Monitoring System II (MMS II) and the Generator Monitoring System (GMS) {7490}
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Carrier Roller - Install
Power Module Switchgear (Low Voltage and Medium Voltage) Initial Startup Procedure
3126 Truck Engine Flywheel Housing
Power Module Switchgear (Low Voltage and Medium Voltage) General Maintenance Information
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Carrier Roller - Disassemble
C7 and C9 On-Highway Engines 0186-04 PTO Engine Shutdown Switch voltage low
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Carrier Roller - Assemble
3126 Truck Engine Engine Oil Pan
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Roller - Remove
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Roller - Disassemble
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Roller - Assemble