Track Carrier Roller - Disassemble
Disassembly Procedure
Start By:
- Remove the track carrier rollers. Refer to Disassembly and Assembly, "Track Carrier Roller - Remove" in this manual.
- Thoroughly clean the outside of the track carrier roller prior to disassembly.
- Remove plug (2). Drain the oil from the carrier roller into a suitable container for disposal. The capacity of the track carrier roller is 85 ± 5 mL (2.89 ± .17 oz).
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
 | |
| Illustration 1 | g00365386 |
- Remove three socket head bolts (1) and cover (3) from the track carrier roller.
- Remove O-ring seal (4) from cover (3) .
Show/hide table
 | |
| Illustration 2 | g00365954 |
- Remove socket head bolts (5) and (6) and retainer (7) from the end of the shaft assembly.
Show/hide table
 | |
| Illustration 3 | g00365960 |
- Carefully remove shaft assembly (8) from the track carrier roller.
Show/hide table
 | |
| Illustration 4 | g00365964 |
- Remove Duo-cone seal kit (9) from the track carrier roller.
Show/hide table
 | |
| Illustration 5 | g00365965 |
- Remove Duo-cone seal kit (10) from shaft assembly (8) .
Show/hide table
 | |
| Illustration 6 | g00367057 |
- Measure distance (X) on the shaft assembly. Record this dimension for assembly purposes. Use a press to push shaft (8) out of collar (11). Remove the O-ring seal from the inside of the collar.
Show/hide table
 | |
| Illustration 7 | g00367112 |
- Remove bearings (12) and (13) from the track carrier roller.
Show/hide table
 | |
| Illustration 8 | g00367133 |
Show/hide table
 | |
| Illustration 9 | g00367312 |
Caterpillar Information System:
Power Module Switchgear (Low Voltage and Medium Voltage) General Maintenance Information
3126 Truck Engine Flywheel Housing
Power Module Switchgear (Low Voltage and Medium Voltage) Initial Startup Procedure
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Carrier Roller - Install
2001/11/01 Changes were made in the Communication Link for the Marine Monitoring System II (MMS II) and the Generator Monitoring System (GMS) {7490}
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Carrier Roller - Remove
3126B and 3126E On-highway Engines 0128-04 Secondary Fuel Level voltage low
3126B and 3126E On-highway Engines 0128-03 Secondary Fuel Level voltage high
Power Module Switchgear (Low Voltage and Medium Voltage) Initial Startup Safety Check
Power Module Switchgear (Low Voltage and Medium Voltage) Installation
3126B and 3126E On-highway Engines 0096-04 Fuel Level voltage low
Power Module Switchgear (Low Voltage and Medium Voltage) Handling
C7 and C9 On-Highway Engines 0186-04 PTO Engine Shutdown Switch voltage low
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Carrier Roller - Assemble
3126 Truck Engine Engine Oil Pan
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Roller - Remove
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Roller - Disassemble
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Roller - Assemble
3126B and 3126E On-highway Engines 0186-14 PTO Engine Shutdown Switch Occurrence (47)
SCT673 Truck Mounted PumperPOD Hydraulic System Oil Filter - Replace - Gear Case
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Roller - Install
3054 and 3056 Marine Generator Set Engines Alternator and Regulator
3126B and 3126E On-highway Engines 0231-11 J1939 Data Link Fault (58)
G3500B Engines Plate Locations and Film Locations