Track Roller - Disassemble
Disassembly Procedure
Start By:
- Remove the track rollers. Refer to Disassembly and Assembly, "Track Roller - Remove" in this manual.
- Thoroughly clean the outside of the track roller prior to disassembly.
- Drive plug (1) into the stopper in the end of the track roller. Drain the oil from the track roller into a suitable container for disposal. The capacity of the track roller is 225 ± 10 mL (7.70 ± .34 oz).
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
Illustration 1 | g00367837 |
- Put the track roller in a press, as shown. The weight of the track roller is approximately 34 kg (75 lb). Press on end collar (3). Remove retaining ring (2). Release the pressure on the end collar. Remove end collar (3) .
Show/hide table
Illustration 2 | g00367838 |
- Remove plug (1) from the inside of the track roller.
- Remove Duo-cone seal kit (4) from end collar (3) .
Show/hide table
Illustration 3 | g00367844 |
- Remove the O-ring seal from shaft (5). Remove shaft (5) from roller (6) .
Show/hide table
Illustration 4 | g00367852 |
- Remove Duo-cone seal kit (9) from end collar (8) .
Show/hide table
Illustration 5 | g00367857 |
- Remove spring pin (7) from end collar (8) and shaft (5). Use a press to remove shaft (5) from end collar (8). Remove the remaining O-ring seal from shaft (5) .
- Remove Duo-cone seal kit (10) from each end of the track roller.
Show/hide table
Illustration 6 | g00367858 |
- Use a press to remove bearing (11) from each end of the track roller.
Show/hide table
Illustration 7 | g00367862 |
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Roller - Remove
3126 Truck Engine Engine Oil Pan
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Carrier Roller - Assemble
C7 and C9 On-Highway Engines 0186-04 PTO Engine Shutdown Switch voltage low
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Carrier Roller - Disassemble
Power Module Switchgear (Low Voltage and Medium Voltage) General Maintenance Information
3126 Truck Engine Flywheel Housing
Power Module Switchgear (Low Voltage and Medium Voltage) Initial Startup Procedure
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Carrier Roller - Install
2001/11/01 Changes were made in the Communication Link for the Marine Monitoring System II (MMS II) and the Generator Monitoring System (GMS) {7490}
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Carrier Roller - Remove
3126B and 3126E On-highway Engines 0128-04 Secondary Fuel Level voltage low
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Roller - Assemble
3126B and 3126E On-highway Engines 0186-14 PTO Engine Shutdown Switch Occurrence (47)
SCT673 Truck Mounted PumperPOD Hydraulic System Oil Filter - Replace - Gear Case
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track Roller - Install
3054 and 3056 Marine Generator Set Engines Alternator and Regulator
3126B and 3126E On-highway Engines 0231-11 J1939 Data Link Fault (58)
G3500B Engines Plate Locations and Film Locations
3054 and 3056 Engines 520 Generator Set Control Panel Control Module - Configure
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track - Separate
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Track - Connect
CIPI UNDERCARRIAGE Arrangements: 9Q-5262, 191-4041, and 204-9207 Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install
3126B and 3126E On-highway Engines 0231-02 J1939 Data Incorrect (58)