Control Valve (Snow Plow/Dozer Angle)
Show/hide table
Illustration 1 | g06335898 |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
1 | 2 | 361-3549 O-Ring Seal | Lubricate seal lightly with fluid being sealed. |
2 | 2 | 3K-0360 O-Ring Seal | Lubricate seal lightly with fluid being sealed. |
3 | 2 | 9J-0403 Spring | Test length is Test force is Free length after test is |
4 | 1 | 108-2187 Pipe Plug | Torque to |
5 | 1 | 6E-5153 Spring | Test length is Test force is Free length after test is |
6 | 2 | 9J-0404 Plug | Torque to |
7 | 1 | 139-8472 Relief Valve Gp | Torque to |
8 | 1 | 111-8233 Spring | Spring must have Light blue stripe
Length under test force is Test force is Free length after test is |
9 | 1 | 5B-9318 Ball | During assembly, lightly seat the ball into the body. |
10 | 1 | 6E-3007 Spring | Length under test force is Test force is Free length after test is |
11 | 1 | 102-7412 Spring | Length under test force is Test force is Free length after test is |
12 | 2 | 8M-4437 O-Ring Seal | Lubricate seal lightly with fluid being sealed. |
13 | 1 | 101-1971 Lever | Torque to |
Caterpillar Information System:
2001/08/01 A New Piston and Piston Rings Are Now Available {1214, 1215}
HDB Series and M1 Series Heavy Duty Brushless Alternators Residual Magnetism - Restore
3412E, C30 and C32 Marine Engines Engine Oil Filter Base - Assemble
2001/08/01 Additional Troubleshooting Procedures For Speed Burps {1901, 1913}
2001/08/01 Oil Pan No Longer Requires Gasket Sealant {1302}
HDB Series and M1 Series Heavy Duty Brushless Alternators Rectifier - Test
3412E, C30 and C32 Marine Engines Engine Oil Filter Base - Disassemble
HDB Series and M1 Series Heavy Duty Brushless Alternators Stator - Test
3412E, C30 and C32 Marine Engines Engine Oil Filter Base - Install
3412E, C30 and C32 Marine Engines Engine Oil Filter Base - Remove
HDB Series and M1 Series Heavy Duty Brushless Alternators Capacitor - Test
G3600 Engines Aftercooler
3126B Marine Engines ECM Will Not Communicate with Other Systems or Display Modules
3064 and 3066 Engines for Caterpillar Built Machines Engine Speed - Check
2001/08/01 When These Control Groups Are Used As Service Replacements, Use This Procedure For The Initial Setup Of The 203-7810 Engine Monitoring Control Group And The 203-7811 Engine Monitoring Control Group {1901, 7490}
2001/10/01 The Oil Pan No Longer Requires Gasket Sealant {1302}
3512 Industrial Engine Engine Oil Pan
G3600 Engines Engine Oil Temperature Regulator
G3600 Engines Ignition System
3408E and 3412E Industrial Engines Throttle Position Sensor - Calibrate
3126B Marine Engines Diagnostic Codes
3512B Marine Auxiliary Engine Vibration Sensor
SBF214 and SUF557 Skid Mounted Power Packs Maintenance Interval Schedule
2001/11/01 A New Temperature Indicator Assembly Is Available To Measure The Temperature Of The Air In The Air Inlet Manifold {1058, 7450}