Engine Oil Pan
Show/hide table
图 1 | g02843936 |
俯视图 |
Show/hide table
图 2 | g02843937 |
右视图 典型示例 |
Show/hide table
技术规格 - 8N-6164 油底壳总成和 152-6013 油底壳总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
- | 15 | 1A-2029 螺栓 | 按照以下步骤拧紧螺栓: |
1. 将五根螺栓 (12) 拧紧到标准扭矩。 | |||
2. 按图 1 中所示的数字顺序将螺栓 (1) 至螺栓 (10) 拧紧至标准扭矩。 | |||
11 | - | - | 装配前,在垫片的接头上涂抹红色 Loctite 593 或 Loctite 5399。 |
13 | - | - | 装配前,用要密封的润滑剂或经认可的等效物稍稍润滑 O 形密封圈的孔。 |
14 | - | - | 组装前,在飞轮壳 (17) 的连接接头、缸体后部、前部附件驱动壳体 (18) 的连接接头和缸体前部涂抹红色 Loctite 593 或 Loctite 5399。 |
15 | 1 | 142-4159 整体式密封件 | 装配前,将红色 Loctite 593 或 Loctite 5399 涂覆到密封表面上。 |
16 | 38 | 5P-5855 螺栓 | 组装完油底壳后,将蓝色 Loctite 243 涂敷在螺栓孔的开顶端。 |
19 | 1 | 4B-2363 机油排放塞 | 拧紧至扭矩为 |
20 | 1 | 6I-0723 机油排放塞 | 拧紧至扭矩为 |
Caterpillar Information System:
2001/10/01 The Oil Pan No Longer Requires Gasket Sealant {1302}
2001/08/01 When These Control Groups Are Used As Service Replacements, Use This Procedure For The Initial Setup Of The 203-7810 Engine Monitoring Control Group And The 203-7811 Engine Monitoring Control Group {1901, 7490}
3064 and 3066 Engines for Caterpillar Built Machines Engine Speed - Check
3126B Marine Engines ECM Will Not Communicate with Other Systems or Display Modules
120H and 135H Motor Graders Hydraulic and Steering System Control Valve (Snow Plow/Dozer Angle)
2001/08/01 A New Piston and Piston Rings Are Now Available {1214, 1215}
HDB Series and M1 Series Heavy Duty Brushless Alternators Residual Magnetism - Restore
3412E, C30 and C32 Marine Engines Engine Oil Filter Base - Assemble
2001/08/01 Additional Troubleshooting Procedures For Speed Burps {1901, 1913}
2001/08/01 Oil Pan No Longer Requires Gasket Sealant {1302}
HDB Series and M1 Series Heavy Duty Brushless Alternators Rectifier - Test
3412E, C30 and C32 Marine Engines Engine Oil Filter Base - Disassemble
G3600 Engines Engine Oil Temperature Regulator
G3600 Engines Ignition System
3408E and 3412E Industrial Engines Throttle Position Sensor - Calibrate
3126B Marine Engines Diagnostic Codes
3512B Marine Auxiliary Engine Vibration Sensor
SBF214 and SUF557 Skid Mounted Power Packs Maintenance Interval Schedule
2001/11/01 A New Temperature Indicator Assembly Is Available To Measure The Temperature Of The Air In The Air Inlet Manifold {1058, 7450}
SPS342 Skid Mounted Pumper Maintenance Interval Schedule
2001/08/01 A Special Instruction Is Available For Replacing Starting Motor Solenoids {1467}
Electronic Modular Control Panel II (EMCP II) Fault Description
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Engine Starting with Jump Start Cables
2001/09/01 Repair Procedure for the Threads in a Cylinder Head Casting that were Damaged by a Manual Valve Group (Kiene Valve) {1100}