Governor Drive - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 5P-0944     | Dowel Puller Group     | 1     |
B     | 1P-0510     | Driver Group     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install seals (13) in the housing.
Show/hide table
Illustration 1 | g00783929 |
- Install bearings (12) in the housing with Tooling (B) .
Show/hide table
Illustration 2 | g00783927 |
- Fill the sump in the housing with 3 L (3.17 qt) of clean oil.
Show/hide table
Illustration 3 | g00791633 |
- Install bearings (11) with Tooling (A) . Install shafts (10) .
Show/hide table
Illustration 4 | g00783963 |
- Raise the temperature of gear (9) to a maximum temperature of 135 °C (275 °F) and install the gear on shaft assembly (8) .
Show/hide table
Illustration 5 | g01422211 |
- Use a press to install the dowel in shaft assembly (8) to a height of 0.34 ± 0.025 mm (0.013 ± 0.0010 inch).
- Install shaft assembly (8) in the housing.
Show/hide table
Illustration 6 | g00783967 |
- Install gears (7) .
- Place the two housings in the original location and install bolts (4) .
Show/hide table
Illustration 7 | g00783890 |
- Install bolts (6) and service meter (5) .
- Install cover (3) , bolts (2) , and the washers . Install two bolts (1) . Install a new gasket.
Show/hide table
Illustration 8 | g00783882 |
- Refer to Specifications Manual, "Governor Drive".
End By: Install governor drive. Refer to Disassembly and Assembly, "Governor Drive - Install".
Caterpillar Information System:
XQ300, XQ400 Rental Generator Sets Self-Diagnostics
3126B Engine for Caterpillar Built Machines Engine Speed/Timing Sensor - Calibrate
G3408C and G3412C Engines Governor Drive - Disassemble
3412C Engine Turbocharger Oil Lines
3412C Engine Turbocharger
C-9 Industrial Engine Fan Drive - Install
3412C Engine Valve Mechanism Cover
G3408C and G3412C Engines Governor Drive - Install
Exhaust Temperature Scanner Worksheet
2001/04/01 New Air Shutoff Groups Are Used {1078}
G3408C and G3412C Engines Governor - Remove and Install
G3408C and G3412C Engines Governor Drive - Remove
3412C Engine Aftercooler
G3408C and G3412C Engines Carburetor - Remove
G3408C and G3412C Engines Carburetor - Install
Product Identification Numbers (PIN) Location Guide Compactor (Soil)
G3408C and G3412C Engines Carburetor - Disassemble
3412C Engine Cylinder Block
37-MT, 41-MT, and 42-MT Series Starting Motors Engine Does Not Crank with Starting Motor On and Pinion Engaging Ring Gear
3412C Engine Engine Oil Pan
G3408C and G3412C Engines Carburetor - Assemble
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Parallel Operation
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies System Startup
3054 and 3056 Marine Generator Sets Warning Alarm