Crankshaft
Show/hide table
 | |
| 图 1 | g01419944 |
(1) 止推板 | |
有关详情，请参考技术参数, "连杆和主轴承轴颈"部分。
(B) 新曲轴的轴向间隙 ... 0.17 至 0.63 毫米 (0.007 至 0.025 英寸)
(2) 螺塞的扭矩 ... 50 ± 7 牛米 (37 ± 5 磅英尺)
注: 不要重复使用配重螺栓。
(3) 请采用以下步骤拧紧螺栓：
- 组装前，请先用 6V-4876 润滑剂 来润滑螺栓螺纹、螺栓杆、 垫圈和螺栓头底部。
- 以 200 ± 5 牛米 (145 ± 4 磅英尺)的扭矩均匀地拧紧螺栓。
- 松开螺栓。
- 再次以 70 ± 5 牛米 (50 ± 4 磅英尺)的扭矩均匀地拧紧螺栓。
- 将各个螺栓再旋转 120 ± 5 度。
Caterpillar Information System:
SPS342 Skid Mounted Pumper Fuel System Primary Filter/Water Separator - Drain
2000/06/01 Disregard Special Instruction, REHS0780-00 , "Programming The Electronic Ignition System (EIS) Control Module For The Manifold Air Pressure (MAP) Sensor" {1408, 1901}
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0269 - FMI 04
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0269 - FMI 03
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0566 - FMI 07 (for PEEC Engines)
3500B Marine Engines Diagnostic Codes
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0566 - FMI 07 (for EUI Engines)
37-MT, 41-MT, and 42-MT Series Starting Motors General Information
G3516B Engines Throttle Actuator
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0566 - FMI 07 (for MUI Engines)
EMCPII+ for Gas Engines GSC CID 0500 - FMI 12
EMCPII+ for Gas Engines GSC CID 0475 - FMI 04
EMCPII+ for Gas Engines GSC CID 0333 - FMI 03
EMCPII+ for Gas Engines GSC CID 0333 - FMI 04
SPS342 Skid Mounted Pumper Fuel System Primary Filter (Water Separator) Element - Replace
G3516B Engines Desired Speed Input (4 - 20 mA)
EMCPII+ for Gas Engines GSC CID 0268 - FMI 02
EMCPII+ for Gas Engines GSC CID 0336 - FMI 02
G3516B Engines Detonation Sensors
PM3412C Power Modules Equipment Parking
37-MT, 41-MT, and 42-MT Series Starting Motors Service Tools
37-MT, 41-MT, and 42-MT Series Starting Motors Component Description
Electronic Modular Control Panel II+ (EMCP II+) Indicator for Overcrank (for PEEC Engines)
C-10, C-12, 3406E, C-15, C-16 and C-18 Engines - Electronic PTO Installation and Application General Information