GSC CID 0500 - FMI 12
产生此代码的情况:
CID 500 FMI 12意味着 GSC+不能精确测量交流电压和交流电流。 发动机保持运转状态。 发动机仍然能起动。
注: GSC+ 上，即使发动机控制开关位于关闭/复位（OFF/RESET）位置，CID 500 FMI 12诊断代码同样会出现。
测试步骤 1. 确认诊断代码为激活状态。
- 代码 CID 500 FMI 12处于激活状态。
Show/hide table
| 注意 |
|---|
如果出现 CID 500 FMI 12，并且发动机正在运转，那么调速器输出可能位于满伏电压状态。 即使 GSC 显示 0 AC 并且所有三相电流都为 0 AC，这也会发生。 |
预期结果:
代码 CID 500 FMI 12处于激活状态。
结果:
- 是 - 代码 CID 500 FMI 12处于激活状态。
修复: 更换 GSC+。 参见测试与调整, " EMCP 发电机组电子控制装置更换"。
停止
- 否 - 代码 CID 500 FMI 12为非激活状态。
修复: GSC+ 运转正常。
停止
Caterpillar Information System:
EMCPII+ for Gas Engines GSC CID 0475 - FMI 04
PM3516 Power Modules Engine Oil and Filter - Change
EMCPII+ for Gas Engines GSC CID 0475 - FMI 03
G3516B Engines Engine Speed/Timing Sensor
37-MT, 41-MT, and 42-MT Series Starting Motors Starting Motor
Medium Wheel Loaders (MWL) Payload Control System (PCS) 3.0 Wiring Harness (Short Circuit) - Test
C9 On-highway Engines Fuel System Primary Filter - Replace
Payload Control System (PCS) 2.X Wiring Harness (Open Circuit) - Test
Programmable Relay Control Module (PRCM) Glossary of Terms
3608 Engine Air Prelube Pump Lubricator Oil Level - Check
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>7W-1877</B> Generator through <B>7W-8825</B> Generator
Programmable Relay Control Module (PRCM) Connector Contact Identification
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0566 - FMI 07 (for MUI Engines)
G3516B Engines Throttle Actuator
37-MT, 41-MT, and 42-MT Series Starting Motors General Information
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0566 - FMI 07 (for EUI Engines)
3500B Marine Engines Diagnostic Codes
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0566 - FMI 07 (for PEEC Engines)
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0269 - FMI 03
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0269 - FMI 04
2000/06/01 Disregard Special Instruction, REHS0780-00 , "Programming The Electronic Ignition System (EIS) Control Module For The Manifold Air Pressure (MAP) Sensor" {1408, 1901}
SPS342 Skid Mounted Pumper Fuel System Primary Filter/Water Separator - Drain
3508B Engine for Caterpillar Built Machines Crankshaft
EMCPII+ for Gas Engines GSC CID 0333 - FMI 03