Control Manifold (Hydraulic Fan) - Remove and Install
Start By:
- Remove the hood (cooling package).
Show/hide table
 |
|
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
- Release the system pressure. Refer to Operation and Maintenance Manual, "System Pressure - Release" for the correct procedure.
- Drain the hydraulic oil. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct draining and filling procedures.
Show/hide table
Illustration 1 g06134484 - Disconnect hose assemblies (1) and (2).
Show/hide table
Illustration 2 g06134551 - Disconnect harness assemblies (3).
- Remove two bolts (5) and control manifold (4).
- Install control manifold (4) in the reverse order of removal.
Caterpillar Information System:
PM310, PM312, and PM313 Cold Planer Water Spray System - Inspect
New Hose Clamps are Now Used in the Coolant Lines Group of Certain 700 Series Articulated Trucks {1087, 1380} New Hose Clamps are Now Used in the Coolant Lines Group of Certain 700 Series Articulated Trucks {1087, 1380}
PM310, PM312, and PM313 Cold Planer Steering Cylinder Ends - Lubricate
PM310, PM312, and PM313 Cold Planer Rotor Drive Clutch Bearings - Lubricate
PM310, PM312, and PM313 Cold Planer Rotor Drive Belt - Inspect
An Alignment Procedure for the Fan Support Group as Part of the Radiator Guard Group Is Now Used on the 836K Landfill Compactor {0635, 1353, 1356, 1360, 1386, 7251} An Alignment Procedure for the Fan Support Group as Part of the Radiator Guard Group Is Now Used on the 836K Landfill Compactor {0635, 1353, 1356, 1360, 1386, 7251}
MD6200 Rotary Drill Cab Air Filter (Fresh Air) - Clean/Replace
725C2 and 730C2 Articulated Truck Machine System Rear Suspension Frame - Remove and Install
An Improved Paint Masking Process Is Now Used on the Front Axle Steering Cylinders for Certain Backhoe Loaders {4303, 4313} An Improved Paint Masking Process Is Now Used on the Front Axle Steering Cylinders for Certain Backhoe Loaders {4303, 4313}
C175–16 Locomotive Engine Air in Fuel - Test
2570D and 2670D Wheel Feller Buncher Engine Supplement Engine - Remove and Install
725C2 and 730C2 Articulated Truck Machine System Center Suspension Frame - Remove and Install
PM310, PM312, and PM313 Cold Planer Water Spray System Fluid Level - Check
MH3037 Material Handler Engine Supplement Turbocharger - Remove and Install - Second Stage Turbocharger
CP54B, CS54B and CS64B Soil Compactors Machine Systems Operator Controls (Vibratory System)
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Electric Drive Pump (Powered Stairway) Oil Level - Check - If Equipped
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Manual Lowering (Powered Stairway) - Test - If Equipped
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Platform (Powered Stairway) - Lubricate - If Equipped
730C2 and 725C2 Articulated Truck Power Train Front Axle - Remove and Install
PM310, PM312, and PM313 Cold Planer Lower Conveyor Deflectors (First Stage) - Inspect/Replace
PM310, PM312, and PM313 Cold Planer Moldboard Cutting Edge - Inspect/Adjust/Replace
PM310, PM312, and PM313 Cold Planer Rotor Bearing Oil - Change
PM310, PM312, and PM313 Cold Planer Rotor Bearing Oil Level - Check
Cat Activate Mobile Application User Guide {7606, 7620} Cat Activate Mobile Application User Guide {7606, 7620}