Electric Drive Pump (Powered Stairway) Oil Level - Check - If Equipped
a. Prepare the machine for maintenance. Refer to Operation and Maintenance Manual, "Prepare the Machine for Maintenance".
- Remove the bolts from the tread plates, and store the bolts for reuse.
- Remove the tread plates, and store the plates for reuse.
Show/hide table
| |
| Illustration 1 | g06134389 |
- Check the oil level. If the oil level is below the FULL mark, remove the filler cap and add oil to the reservoir to raise the oil level to the FULL mark.
Note: Maintain the oil volume at the FULL level. Do not operate the powered stairway when the oil level is below the PUMP MIN level.
Show/hide table
| |
| Illustration 2 | g06134371 |
Note: The oil level for the powered stairway is visible through the clear plastic oil reservoir.
- Install the tread plates.
- Install the bolts for the tread plates, and tighten the bolts to the proper torque.
Show/hide table
| |
| Illustration 3 | g06134391 |
Caterpillar Information System:
CP54B, CS54B and CS64B Soil Compactors Machine Systems Operator Controls (Vibratory System)
MH3037 Material Handler Engine Supplement Turbocharger - Remove and Install - Second Stage Turbocharger
PM310, PM312, and PM313 Cold Planer Water Spray System Fluid Level - Check
563D and 573D Wheel Feller Buncher Machine Systems Control Manifold (Hydraulic Fan) - Remove and Install
PM310, PM312, and PM313 Cold Planer Water Spray System - Inspect
New Hose Clamps are Now Used in the Coolant Lines Group of Certain 700 Series Articulated Trucks {1087, 1380} New Hose Clamps are Now Used in the Coolant Lines Group of Certain 700 Series Articulated Trucks {1087, 1380}
PM310, PM312, and PM313 Cold Planer Steering Cylinder Ends - Lubricate
PM310, PM312, and PM313 Cold Planer Rotor Drive Clutch Bearings - Lubricate
PM310, PM312, and PM313 Cold Planer Rotor Drive Belt - Inspect
An Alignment Procedure for the Fan Support Group as Part of the Radiator Guard Group Is Now Used on the 836K Landfill Compactor {0635, 1353, 1356, 1360, 1386, 7251} An Alignment Procedure for the Fan Support Group as Part of the Radiator Guard Group Is Now Used on the 836K Landfill Compactor {0635, 1353, 1356, 1360, 1386, 7251}
MD6200 Rotary Drill Cab Air Filter (Fresh Air) - Clean/Replace
725C2 and 730C2 Articulated Truck Machine System Rear Suspension Frame - Remove and Install
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Manual Lowering (Powered Stairway) - Test - If Equipped
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Platform (Powered Stairway) - Lubricate - If Equipped
730C2 and 725C2 Articulated Truck Power Train Front Axle - Remove and Install
PM310, PM312, and PM313 Cold Planer Lower Conveyor Deflectors (First Stage) - Inspect/Replace
PM310, PM312, and PM313 Cold Planer Moldboard Cutting Edge - Inspect/Adjust/Replace
PM310, PM312, and PM313 Cold Planer Rotor Bearing Oil - Change
PM310, PM312, and PM313 Cold Planer Rotor Bearing Oil Level - Check
Cat Activate Mobile Application User Guide {7606, 7620} Cat Activate Mobile Application User Guide {7606, 7620}
Installing The 523-4907 Work Tool Positioner Kit {5112, 5264, 5479} Installing The 523-4907 Work Tool Positioner Kit {5112, 5264, 5479}
Installing The 523-4908 Work Tool Positioner Kit {5112, 5264, 5479} Installing The 523-4908 Work Tool Positioner Kit {5112, 5264, 5479}
PM310, PM312, and PM313 Cold Planer Water Tank Strainer - Clean and Inspect
PM820, PM822, and PM825 Cold Planer Machine Systems Antislab - Remove and Install