Rear Suspension Frame - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1U-9199 | Lever Puller | 2 |
B | 1P-0520 | Driver Group | 1 |
Start By:
- Remove the rear axle stabilizer rod.
- Remove the rear drive shaft.
Show/hide table
Personal injury or death can result from improper lifting or blocking. When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component. Approximate weights of the components are shown. Clean all surfaces where parts are to be installed. |
- Remove bolt (1) and clip (2).
Show/hide table
Illustration 2 g06134128 Show/hide tableIllustration 3 g06134138 - Attach Tooling (A) and a suitable lifting device to each side of the rear of rear suspension frame (3).
Show/hide table
Illustration 4 g06134333 Show/hide tableIllustration 5 g06134336 - Attach Tooling (A) and a suitable lifting device to the front of the rear suspension frame .
- Disconnect hose assembly (4)
- Remove nut (5), washer (7), and bolt (6).
Show/hide table
Illustration 6 g06134345 - Remove pin (8).
Show/hide table
Illustration 7 g06134347 - Use two people to remove bracket (11). The weight of bracket (11) is approximately
24 kg (53 lb) . - Remove bolts (9) and bracket (11) from rear axle (10).
Show/hide table
Illustration 8 g06134348 - Remove bolts (12) from rear axle (10).
- Use Tooling (A) to lower the rear suspension frame to the ground. The weight of the rear suspension frame is approximately
94 kg (207 lb) . Lower and remove the rear suspension frame from the rear axle.Show/hide tableIllustration 9 g06134349 - Remove bolts (13) and clamp ring (14).
Show/hide table
Illustration 10 g06134352 - Use Tooling (B) to remove bearing (15). Remove bearing (15).
Show/hide table
Illustration 1 | g06134123 |
- Install rear suspension frame (3) in the reverse order of removal.
- Tighten bolts (12) and (9) to a torque of
900 ± 100 N·m (664 ± 74 lb ft) .
- Tighten bolts (12) and (9) to a torque of
Caterpillar Information System:
An Improved Paint Masking Process Is Now Used on the Front Axle Steering Cylinders for Certain Backhoe Loaders {4303, 4313} An Improved Paint Masking Process Is Now Used on the Front Axle Steering Cylinders for Certain Backhoe Loaders {4303, 4313}
C175–16 Locomotive Engine Air in Fuel - Test
2570D and 2670D Wheel Feller Buncher Engine Supplement Engine - Remove and Install
725C2 and 730C2 Articulated Truck Machine System Center Suspension Frame - Remove and Install
994K Wheel Loader Machine Systems Lift Cylinder - Remove and Install
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Ride Control Accumulator - Test and Charge
797F and 797F XQ Off-Highway Trucks Magnetic Plug (Pump Drive, Hydraulic) - Check
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B} M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Editing Truck and Material Lists
785G Off-Highway Truck Systems Electronic Control Module (ECM) - Replace
PM310, PM312, and PM313 Cold Planer Legs (Struts) - Lubricate
PM310, PM312, and PM313 Cold Planer Hydraulic System Oil Sample - Obtain
MD6200 Rotary Drill Cab Air Filter (Fresh Air) - Clean/Replace
An Alignment Procedure for the Fan Support Group as Part of the Radiator Guard Group Is Now Used on the 836K Landfill Compactor {0635, 1353, 1356, 1360, 1386, 7251} An Alignment Procedure for the Fan Support Group as Part of the Radiator Guard Group Is Now Used on the 836K Landfill Compactor {0635, 1353, 1356, 1360, 1386, 7251}
PM310, PM312, and PM313 Cold Planer Rotor Drive Belt - Inspect
PM310, PM312, and PM313 Cold Planer Rotor Drive Clutch Bearings - Lubricate
PM310, PM312, and PM313 Cold Planer Steering Cylinder Ends - Lubricate
New Hose Clamps are Now Used in the Coolant Lines Group of Certain 700 Series Articulated Trucks {1087, 1380} New Hose Clamps are Now Used in the Coolant Lines Group of Certain 700 Series Articulated Trucks {1087, 1380}
PM310, PM312, and PM313 Cold Planer Water Spray System - Inspect
563D and 573D Wheel Feller Buncher Machine Systems Control Manifold (Hydraulic Fan) - Remove and Install
PM310, PM312, and PM313 Cold Planer Water Spray System Fluid Level - Check
MH3037 Material Handler Engine Supplement Turbocharger - Remove and Install - Second Stage Turbocharger
CP54B, CS54B and CS64B Soil Compactors Machine Systems Operator Controls (Vibratory System)
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Electric Drive Pump (Powered Stairway) Oil Level - Check - If Equipped